Need help?Do you have a question about the Boss Gigcaster 5 and is the answer not in the manual?
General| Channels | 5 |
|---|---|
| Sampling Rate | 48kHz |
| Bit Depth | 24-bit |
| Internal Storage | No |
| Inputs - Mic Preamps | 4 x XLR/TRS Combo |
| Phantom Power | Yes |
| USB | Yes |
| Computer Connectivity | USB |
| USB Audio Interface | Yes |
| Built-in Effects | Yes, Reverb, Compressor, Noise Suppressor, De-Esser, Enhancer, Voice FX, Sound Pads |
| Outputs - Main | 2 |
Configures settings for channels 1 and 2.
Sets the input source and gain for channels.
Adjusts the equalization for channels.
Configures and selects effects for channels.
Configures general settings for the channel.
Configures dedicated effects for the sound pad.
Configures general settings for the sound pad.
Lists functions assignable to pads.
Lists functions assignable to pads for FUNCTION A.
Lists functions assignable to pads for FUNCTION B-D.
Configuration for CTL/EXP footswitch or expression pedal.
Defines functions for CTL1 and CTL2 footswitches.
Lists functions assignable to CTL1 and CTL2.
Lists functions assignable to footswitches for FUNCTION A.
Lists functions assignable to footswitches for FUNCTION B-D.
Configuration for expression pedals.
Lists functions assignable to expression pedals.
Lists functions assignable to expression pedals for FUNCTION B-D.
Configuration for the GA-FC controller.
Defines functions for GA-FC pedals 1-6.
Lists functions assignable to GA-FC pedals.
Lists functions assignable to GA-FC pedals for FUNCTION A.
Lists functions assignable to GA-FC pedals for FUNCTION B-D.
Details specific settings for EXP1 and EXP2 pedals.
Lists functions assignable to EXP1 and EXP2.
General settings for foot switch connections.
Specifies PAD LINK settings for GA-FC.
Configures the main audio output.
Adjusts the equalization for the main output.
Configures settings for headphone outputs.
Configures USB main and monitor outputs.
Sets the signal input level for USB auxiliary input.
Configures talkback function settings.
Configures COMP, REVERB, and GENERAL effects.
Manages system version, date, backup, and reset.
Adjusts display brightness and settings.
Configures USB audio operating modes.
Manages system version, date, backup, and reset.
Adds distortion to the sound for long sustain.
Selects the type of distortion effect.
Simulates guitar amplifier circuits and sound.
Selects the simulated speaker cabinet.
Selects the simulated microphone type.
Reduces unwanted noise and hum.
Adjusts the tone and frequency response.
Controls wah or pitch bend effects via expression pedal.
Provides pitch bend effect using the pedal.
Applies a wah effect using the pedal.
Selects effects for FX1, FX2, and FX3 slots.
Simulates the tonal character of an acoustic guitar.
Enhances acoustic guitar sound quality.
Creates an automatic wah effect via filtering.
Adds detuned sound for depth and breadth.
Applies chorus effect specifically for bass.
Creates a unique undulation effect.
Produces long sustain by evening out input volume.
Simulates a fretless guitar sound.
Simulates a fretless bass sound.
Generates feedback performance sounds.
Creates a twisting, jet-airplane-like flanging sound.
Adds harmony to voice based on diatonic scales.
Creates human vowel-like sounds.
Adds one or two octaves to the sound.
Applies octave effect to bass guitar.
Adds resonance and richness with pitch-shifted harmonics.
Moves the stereo position of the sound.
Creates a whooshing, swirling sound character.
Changes the pitch of the original sound up or down.
Creates a metallic, out-of-focus sound.
Simulates a rotary speaker sound.
Interrupts sound to create rhythm backing phrases.
Produces a volume-swell effect.
Applies intense pitch bending.
Creates a wah effect responding to guitar level.
Creates wah effect responding to bass level.
Creates cyclic changes in volume.
Creates vibrato by modulating pitch.
Adds delayed sound for body or special effects.
Common parameters applicable to all delay types.
Details different dual delay configurations.
Models Roland RE-201 tape echo sound.
Models Maestro Echoplex tape echo sound.
Models Binson Echorec2 sound.
Allows selection between delay or reverb effects.
Adds reverberation to the sound.
Applies settings to the overall effect patch.
Defines functions for CTL1-4 footswitch/GA-FC.
Defines functions for expression pedals EXP1, 2.
Details effects for vocal processing.
Sharpens sound and controls volume/sibilance.
Reduces noise in the sound.
Corrects pitch instabilities and creates mechanical effects.
Adds natural harmony to vocals.
Selects effects for FX1, FX2, and FX3 slots.
Produces a distorted voice.
Produces a radio voice.
Degrades sound for distinctive character.
Modifies sound brightness by cutting frequencies.
Creates wah effect responding to guitar level.
Creates metallic, out-of-focus sound.
Simulates a rotary speaker sound.
Interrupts sound to create rhythm backing phrases.
Produces a volume-swell effect.
Applies intense pitch bending.
Creates a wah effect responding to guitar level.
Creates wah effect responding to bass level.
Creates cyclic changes in volume.
Creates vibrato by modulating pitch.
Holds sounds for creative effects.
Repeats sound portions for buzzy character.
Common parameters applicable to all delay types.
Details different dual delay configurations.
Models Roland RE-201 tape echo sound.
Models Maestro Echoplex tape echo sound.
Models Binson Echorec2 sound.
Allows selection between delay or reverb effects.
Adds reverberation to the sound.
Applies settings to the overall effect patch.
Defines functions for CTL1-4 footswitch/GA-FC.
Defines functions for expression pedals EXP1, 2.
Details effects for vocal processing.
Sharpens sound and controls volume/sibilance.
Reduces noise in the sound.
Corrects pitch instabilities and creates mechanical effects.
Adds natural harmony to vocals.
Selects effects for FX1, FX2, and FX3 slots.
Produces a distorted voice.
Produces a radio voice.
Degrades sound for distinctive character.
Modifies sound brightness by cutting frequencies.
Creates wah effect responding to guitar level.
Creates metallic, out-of-focus sound.
Adds detuned sound for depth and breadth.
Creates a twisting, jet-airplane-like flanging sound.
Creates cyclic changes in volume.
Creates a whooshing, swirling sound character.
Interrupts sound to create rhythm backing phrases.
Divides audio into ranges and cuts specified region.
Creates vibrato by modulating pitch.
Holds sounds for creative effects.
Repeats sound portions for buzzy character.
Common parameters applicable to all delay types.
Details different dual delay configurations.
Models Roland RE-201 tape echo sound.
Models Maestro Echoplex tape echo sound.
Models Binson Echorec2 sound.
Allows selection between delay or reverb effects.
Adds reverberation to the sound.
Applies settings to the overall effect patch.
Defines functions for CTL1-4 footswitch/GA-FC.
Defines functions for expression pedals EXP1, 2.
Details effects for vocal processing.
Sharpens sound and controls volume/sibilance.
Reduces noise in the sound.
Corrects pitch instabilities and creates mechanical effects.
Adds natural harmony to vocals.
Selects effects for FX1, FX2, and FX3 slots.
Produces a distorted voice.
Produces a radio voice.
Degrades sound for distinctive character.
Modifies sound brightness by cutting frequencies.
Creates wah effect responding to guitar level.
Creates metallic, out-of-focus sound.
Adds detuned sound for depth and breadth.
Creates a twisting, jet-airplane-like flanging sound.
Creates cyclic changes in volume.
Creates a whooshing, swirling sound character.
Interrupts sound to create rhythm backing phrases.
Divides audio into ranges and cuts specified region.
Creates vibrato by modulating pitch.
Holds sounds for creative effects.
Repeats sound portions for buzzy character.
Common parameters applicable to all delay types.
Details different dual delay configurations.
Models Roland RE-201 tape echo sound.
Models Maestro Echoplex tape echo sound.
Models Binson Echorec2 sound.
Allows selection between delay or reverb effects.
Adds reverberation to the sound.
Applies settings to the overall effect patch.
Defines functions for CTL1-4 footswitch/GA-FC.
Defines functions for expression pedals EXP1, 2.
Details effects for talk and conversation.
Adjusts the tone and frequency response.
Selects effects for FX1 and FX2 slots.
Details effects for console operations.
Produces long sustain by evening out volume.
Diagram illustrating the GCS-5's audio signal flow.
To Next Page
