bouncepad Wallmount User Manual

Mount Washer
M4 Split washer
M4 Wing Nut
Mount Washer
M4 Split washer
M4 Locking Nut
7mm Spanner
In the Box
Sheet Code: BP-IM-033_REV2
Release Date: 24/10/2019
Copyright 2016 Spotspot Ltd. (T/A
Bouncepad) all rights reserved.
Condential, no part of this publication
may be reproduced or transmitted in any
form without the written permission of the
copyright holder.
Surface
Mounting Kit
Wallmount
Arm
Fixings Kit
Tablet Set-up Kit
Follow steps A if “Fixing
from below”.
A
Follow steps B if “Fixing
from Above”.
B
Locate and screw the Socket screws
into the Wallmount as shown.
Secure the arm to the
surface. Locking Nuts
oer higher security.
Go to step 1.
A3
A4 A5
Using the Mount washer,
mark the drill hole
locations as shown.
A1
Top
Drill each hole - using the
specied drill size.
A2
Using the Mount Plate,
mark the drill hole
locations as shown.
B1
Mount Plate
Top
4x Ø2.5mm
1x Ø16.0mm
25
mm
Metric Imperial
1"
Maximum Mounting
surface thickness :
34
mm
Metric Imperial
1
5/16"
Minimum Mounting
surface thickness :
4x Ø5.0mm
1x Ø16.0mm
Mount Washer
Ø5.0mm Drillbit
Ø16.0mm Holesaw
*Bouncepad accepts zero responsibility for damage
caused due to incorrect assembly methods.
Top
Faceplate
Case
Pair of Keys
Wallmount
Assembly Instructions
Tools Required:
Pencil
Electric Drill
16mm
Holesaw
*if routing the tablet
cable through your
mounting surface
7mm Spanner
*or adjustable spanner
2.5mm Drillbit
*if xing from above
5.0mm Drillbit
*if xing from below
In the Box
4x No.8
Countersunk,
Self tapping
Screw
4x M4x40mm
Socketset
screw
4x M4x20mm
Buttonhead
screw
4x M4x10mm
Countersunk
Screw
4x M4
Locking
Nut
4x M4
Wing Nut
Fixings List
* Due to the modular nature of our product range
you may receive additional xings in the xings kit
Tighten screw(s) using hand tools, using electric
tools may damage your Bouncepad.
Tighten screw(s) using hand tools, using electric
tools may damage your Bouncepad.
*see overleaf
Drill each hole - using the specied
drill sizes.
B2
Ø16.0mm Holesaw
Ø2.5mm Drillbit
M4x40mm
Socketset
screw
Socket Driver
8x M4 Split
Washer
1x Case
Washer
1x Mount
Washer
1x T20 Pin
Torx Driver Bit

bouncepad Wallmount Specifications

General

Brand	bouncepad
Model	Wallmount
Category	Racks & Stands
Language	English

Summary

Fixing from Below Assembly

Marking Drill Hole Locations

Using the Mount washer, mark the drill hole locations as shown in Step A1.

Drilling Holes for Fixing

Drill each hole using the specified drill size as per Step A2.

Securing Wallmount Screw

Locate and screw the Socket screw into the Wallmount as shown in Step A3.

Securing Arm to Surface

Secure the arm to the surface using Locking Nuts for higher security, as shown in Step A4.

Fixing from Above Assembly

Marking Drill Hole Locations

Using the Mount Plate, mark the drill hole locations as shown in Step B1.

Drilling Holes for Fixing

Drill each hole using the specified drill sizes as per Step B2.

Attaching Wallmount Cover

Locate the Cover to the Wallmount and adhere it with adhesive tabs as per Step B3.

Joining Wallmount & Mount Plate

Join the Wallmount and Mount Plate together in the orientation shown in Step B4.

Securing Wallmount to Surface

Secure the Wallmount to the surface using the 4x countersunk fixings as per Step B5.

Mount Cover Adhesion

Adhere the Mount Cover onto the Mount Plate using the adhesive tabs as shown in Step B6.

Tablet Installation

Attaching Bouncepad Case

Locate and attach the Bouncepad Case to the Wallmount as shown in Step 1.

Removing Bouncepad Faceplate

Unlock and remove the Faceplate from the Bouncepad Case as shown in Step 2.

Installing Tablet Setup Kit

Install the Tablet Setup Kit, which is specific to each tablet device and Bouncepad Case, as per Step 3.

Routing Tablet Cable

Feed the tablet cable through the Bouncepad Case & Wallmount as shown in Step 4.

Placing Tablet & Connecting Power

Place the tablet into the Case and connect to power as shown in Step 5.

Locking Bouncepad Faceplate

Locate and lock the Faceplate onto the Bouncepad Case as shown in Step 6.

Installation Completion

Confirm that the installation is now complete as per Step 7.