To Next Page
M
Megan ClaytonSep 23, 2025
How to fix 'DISCONNECT POWER' message on Brammo Motorcycle?
- RramosstephenSep 23, 2025
To resolve the 'DISCONNECT POWER' message on your Brammo Motorcycle, disconnect AC Power.
How to fix 'DISCONNECT POWER' message on Brammo Motorcycle?
To resolve the 'DISCONNECT POWER' message on your Brammo Motorcycle, disconnect AC Power.
What to do if my Brammo Enertia 2010 Motorcycle displays 'RECHARGE REQUIRED B33'?
If your Brammo Motorcycle displays 'RECHARGE REQUIRED B33', it means the charge (SOC) is at 0%. To resolve this, charge the batteries.
What to do if my Brammo Enertia 2010 displays 'RECHARGE REQUIRED B30'?
If the Brammo Motorcycle displays 'RECHARGE REQUIRED B30', it indicates a critically discharged alarm. You should charge the batteries.
What to do if my Brammo Enertia 2010 Motorcycle displays 'RECHARGE REQUIRED B53'?
If your Brammo Motorcycle displays 'RECHARGE REQUIRED B53', it means there is a critically discharged warning. The solution is to charge the batteries.
What to do if my Brammo Enertia 2010 says 'KICKSTAND DOWN'?
If the Brammo Motorcycle indicates 'KICKSTAND DOWN', it means the kickstand is down. Put the kickstand up.
What to do if my Brammo Enertia 2010 Motorcycle says 'CYCLE THROTTLE SW'?
If the Brammo Motorcycle displays 'CYCLE THROTTLE SW', it means there is a DMC Footswitch Sequence Error. Turn the ON/OFF switch OFF.
What to do if my Brammo Enertia 2010 Motorcycle says 'SERVICE REQ'D B43'?
If the Brammo Motorcycle displays 'SERVICE REQ'D B43', it indicates a Battery Fault: 150A Over Current Alarm. Reduce the throttle.
What to do if my Brammo Enertia 2010 Motorcycle says 'SERVICE REQ'D B42'?
If the Brammo Motorcycle displays 'SERVICE REQ'D B42', it indicates a Battery Fault: 120A Over Current Alarm. Reduce the throttle.
What to do if my Brammo Enertia 2010 Motorcycle says 'ALLOW COOLDOWN B62'?
If the Brammo Motorcycle displays 'ALLOW COOLDOWN B62', it indicates a Battery Fault: 200A Over Current Warning. Reduce the throttle.
What to do if my Brammo Enertia 2010 Motorcycle says 'ALLOW COOLDOWN B64'?
If the Brammo Motorcycle displays 'ALLOW COOLDOWN B64', it indicates a Battery Fault: 300A Over Current Warning. Reduce the throttle.
Essential safety advice including helmet use, practice, defensive riding, visibility, and riding within limits.
Details the function of various gauges, indicators, and displays on the Enertia's dashboard.
Ensures the rider and Enertia are prepared for riding, including personal condition and motorcycle checks.
A checklist of items to inspect on the Enertia before each ride for safety and proper function.
Step-by-step guide to powering up the Enertia for riding.
Instructions on enabling the drive system and using the throttle and brakes for riding.
Step-by-step guide for charging the Enertia and understanding charging indicators.
Outlines the types of inspections and servicing recommendations for the Enertia.
Steps to take if the Enertia gets a flat tire, including repair or transport options.
General| Category | Motorcycle |
|---|---|
| Year | 2010 |
| Motor Type | Permanent Magnet AC |
| Voltage | 72 V |
| Battery Capacity | 3.1 kWh |
| Transmission | Single Speed |
| Final Drive | Belt |
| Front Suspension | Telescopic fork |
| Front Brake | Single Disc |
| Rear Brake | Single Disc |
| Battery | Lithium Phosphate |
| Range | 42 miles (68 km) |
| Charging Time | 4 hours |
| Wheelbase | 54.5 inches |
