Why does the replacement symbol light up on my Braun Pulsonic Pro-System Electric Shaver even after changing shaving parts?
If the replacement symbol lights up on your Braun Electric Shaver after changing shaving parts, it may be because the reset button has not been pushed. Push the reset button for at least 3 seconds to reset the counter.
Why is there an increased consumption of cleaning fluid in my Braun Pulsonic Pro-System?
Increased consumption of cleaning fluid in your Braun Electric Shaver may be caused by a clogged drain in the Clean&Renew station. Clean the drain with a wooden toothpick and regularly wipe the tub clean.
Why are battery segments skipped on my Braun Pulsonic Pro-System Electric Shaver display?
Skipped battery segments on your Braun Electric Shaver display, while the battery capacity is decreasing, can happen if: * The foil and cutter are worn, requiring more power for each shave. In this case, renew the foil & cutter cassette. * The shaving system needs regular oiling, especially after cleaning with water only.
Why is the shaving system of my Braun Electric Shaver still wet after cleaning?
If the shaving system of your Braun Electric Shaver remains wet after the cleaning program, it could be due to: * A clogged drain in the Clean&Renew station. Clean the drain with a wooden toothpick and regularly wipe the tub clean. * Prolonged use of the cleaning cartridge. The alcohol proportion decreases while the oil proportion increases. Remove residue with a cloth.
What to do if cleaning does not start when pressing the start button on my Braun Pulsonic Pro-System Electric Shaver?
If the cleaning cycle doesn't start when you press the start button on your Braun Electric Shaver, check the following: 1. Ensure the shaver is correctly placed in the Clean&Renew station, with the shaver's contacts aligned with those in the station. 2. Verify that the cleaning cartridge contains enough cleaning fluid. If the display lights up red, insert a new cartridge. 3. Make sure the appliance is not in stand-by mode. Press the start button again.
What to do if my Braun Electric Shaver turns off with a fully charged battery?
If your Braun Electric Shaver turns off even with a fully charged battery, it could be because: * The foil and cutter are worn, demanding more power than the motor can provide. Consider renewing the foil & cutter cassette. * The shaving system needs oiling. Regularly oil the shaving system, especially after cleaning it with water only.
Why has the battery performance of my Braun Pulsonic Pro-System dropped significantly?
A significant drop in battery performance in your Braun Electric Shaver could be due to: * Worn foil and cutter, requiring more power for each shave. Renew the foil & cutter cassette. * Regular cleaning with water without lubrication. Apply a drop of light machine oil on top of the foil once a week for lubrication if you regularly clean the shaver with water.
Why has my Braun Pulsonic Pro-System Electric Shaver shaving performance dropped?
A drop in shaving performance of your Braun Electric Shaver may be due to several reasons: * The foil and cutter are worn and need replacement. * Your personal setting of shaving performance has been changed; for a more thorough and faster shave, the green (intensive) setting is recommended. * The shaving system is clogged; try soaking the foil & cutter cassette in hot water with a drop of dish liquid, then rinse and tap it out. Once dry, apply a drop of light machine oil to the foil.
What to do if the replacement symbol lights up after changing shaving parts on my Braun Pulsonic Pro-System Electric Shaver?
If you've recently changed the shaving parts on your Braun Electric Shaver but the replacement symbol is still lit, it likely means the reset button hasn't been pressed. Push the reset button for at least 3 seconds to reset the counter.
How to get rid of the unpleasant smell from my Braun Pulsonic Pro-System Electric Shaver head?
If you notice an unpleasant smell coming from the shaver head of your Braun Electric Shaver, it might be because the shaver head is cleaned with water. When cleaning the shaver head with water, use only hot water and, occasionally, a bit of liquid soap (without abrasive substances). Remember to remove the Foil & Cutter cassette and allow it to dry completely.
General| Technology | Sonic Technology |
|---|---|
| Wet & Dry Use | Yes |
| Cleaning Station Compatible | Yes |
| Travel Lock | Yes |
| Shaver Type | Foil Shaver |
| Power Source | Battery |
| Battery Type | Li-Ion |
| Cordless Runtime | 50 minutes |
| Charging Time | 1 hour |
| Quick Charge | 5 min for 1 shave |
To Next Page