Why do I have a dry mouth and throat when using Byond ResPlus B-30P Bi-Level PAP Medical Equipment?
If you experience a dry mouth and throat while using Byond Medical Equipment, it's likely because you're sleeping with your mouth open, causing pressurized air to pass through your mouth, leading to dryness in the nasal passages and throat. The setting pressure may be too low. Consider consulting your doctor.
How to fix Byond Medical Equipment when nothing displays on the screen?
If nothing displays on the screen or the Main Interface screen does not appear after turning on your Byond Medical Equipment, the power supply may not be connected properly. Disconnect the power plug and then reconnect it.
How to fix too hot air output from Byond ResPlus B-30P Bi-Level PAP Medical Equipment?
If the air output from your Byond Medical Equipment is too hot, the air filter may be clogged with dirt, or the air inlet may be blocked. The device might also be too close to a wall, curtains, or other obstructions. Check and clean the air inlet, replace the filter if necessary, and reposition the device at least 2 inches away from any obstructions.
What to do if nose and/or throat are dry using Byond ResPlus B-30P Bi-Level PAP Medical Equipment?
If your nose and/or throat are dry and/or irritated when using Byond Medical Equipment, the air in the room may be dry. Try turning up the humidifier level or consult your doctor.
Why is my Byond ResPlus B-30P Bi-Level PAP Medical Equipment so loud?
If your Byond Medical Equipment is excessively loud, the tube might not be connected properly, or the mask or tubing may be leaking. Reconnect the tubing and ensure there are no leaks.
What to do if there is water in the mask of Byond Medical Equipment?
If water accumulates in the mask while using Byond Medical Equipment, the room temperature may be too low, or if you're using a humidifier, the output air can condense in the tube. Lower the humidifier setting, increase the room temperature, or place a towel or blanket over the tube to maintain the temperature of the output airflow.
Why is the air flow output too low on Byond ResPlus B-30P Bi-Level PAP Medical Equipment?
If the air flow output from your Byond Medical Equipment is too low, and the Ramp function is on, it may take time for the airflow to rise. The air inlet may also be blocked. Turn off or change the settings of the Ramp feature. Check and clean the air inlet or replace the air filter.
Why does my Byond Medical Equipment beep after turning on?
If your Byond Medical Equipment beeps after turning on, the power supply may not be connected properly. Disconnect the power plug and reconnect it.
Why is my face reddening using Byond ResPlus B-30P Bi-Level PAP Medical Equipment?
If your face becomes red or inflamed while using Byond Medical Equipment, the headgear may be too tight, the mask model or size may not be suitable, or you may be allergic to the mask materials. Loosen the headgear and ensure proper fit. Consult your doctor.
What to do if Byond ResPlus B-30P Bi-Level PAP fails to stop automatically?
If the device fails to stop automatically after removing the mask when using Byond Medical Equipment, the “Auto OFF” function is likely off. Set the “Auto OFF” function to “ON.”
Defines the device's purpose for adult patients with respiratory insufficiency or OSA.
Alerts users to potential risks and hazards associated with device operation.
Highlights actions that might damage the device or injure the user.
Lists conditions where the device should not be used or used with caution.
Step-by-step guide for initial setup and operation of the device.
Details regular usage procedures for the device after initial setup.
Details the components that make up the humidifier unit.
Instructions for attaching and detaching the humidifier from the main unit.
Guide on how to properly fill the humidifier's water tank.
Describes the primary display screens of the device's user interface.
Details the interface for monitoring and adjusting pressure and flow curves.
Guide to accessing and modifying various device settings and parameters.
Instructions for configuring system-level settings like time, date, and language.
Explains how to view device usage data and performance metrics.
Details how to set up and manage device alarms for various conditions.
Recommends a schedule for cleaning and replacing device components.
Outlines the steps for cleaning the device and its accessories.
Specific instructions for cleaning the main unit and the breathing tube.
Steps for cleaning the humidifier's water tank.
Procedures for cleaning and replacing the device's air filter.
Guidelines for disinfecting device components, especially for clinic use.
Procedures for preparing the device when switching between patients.
General| Data Storage | SD Card |
|---|---|
| Operating Voltage | 100-240 V AC, 50/60 Hz |
| Device Type | Bi-Level PAP |
| IPAP Range | 4-30 cmH2O |
| EPAP Range | 4-25 cmH2O |
| Pressure Range | 4-30 cmH2O |
| Rise Time | 1-6 settings |
| Alarms | Power failure, Low pressure |
| Display | LCD screen |
| Power Supply | External AC adapter |
| Humidifier Compatibility | Integrated heated humidifier |
| Humidifier | Integrated heated humidifier |
| Model | Byond ResPlus B-30P |
To Next Page