andcomfortableair.Nomistwill beproduced.Afterapprox.8-12hours,the waterreservoirwillbe
completelyevaporatedintothe airandwill needto berefilled.
HowItWorks:
This unitis a portablefan,as wellsan evaporativeair cooler.Whenusingthe coolingfunction,the
water insidetheunit willbe pumpedthroughoutpipes insideand willbe dispersedontothe cooling
pads. Themotion ofthefan will dragair intothe airintakeareas, whichwillthen passthroughthe
cooling pads.Themovementof thewindoverthe moisturewill evaporateand createnaturallycool
Interior Structure
Exterior Structure
filter
vertical auto
swing louvers
horizontal adjustable
louvers
manual water fill
control panel
side panel(air intake)
water level indicator
swivel casters locking
swivel casters NON-locking
water tank
Remote control
1.“ ”ON/OFF
2.“ ”“ ”“ ”
Increase speeds
3.“ ”“ ”“ ”
Reduce speeds
4.“ ”Cooling mode
5.“ ”Fan mode
6.“ ”Non functional for this model
7.“ ”Auto Swing mode
Troubleshooting:
Please call Cajun KoolingSupport before altering or replacingany parts. Some parts maynot
need full replacementand can be serviced by a technician.1-844-819-3557
swing motor
swing motor
support
motor bracket
fan blades
louver
bracket
horizontal
louver
manual water
inlet
drain cap
water hose
side filter
side louver
cooling pad
support
cooling pad
filter
back panel
(air intake)
motor
control panel
box
electrical
control board
control panel
top cover
water
distributor
side cooling
pad
casters
water sensor
submersible
pump
water tank
side cooling
pad support
side cooling
pad
ProblemPossible CauseSolution
Cannot turn onthe unit1. The power supplyis not connected
2. ON/OFF buttondoes not work
3. Fuse shortage
4. Voltageis too low
1. Check the power supply
2. Replace the controlpanel
3. Check the phasewire (spare fuse available in the box)
4. Check the voltagesupply
The fuse shortsoften1. The water pump hasshut off
3. Motor of the “swing” function is
broken
1. Replace the waterpump
3. Replace the motorfor the “swing”
WaterLeakage from
external parts or
spitting water
1. The machineis not well balanced
2. Water reservoiris leaking
3. Drain is leaking
4. Water level inletis leaking
5. Water level is toohigh
6. Internal pipesfor distribution is
broken or moved
7. Cooling pads dirty
8. Side opening is not fully closed.
1. Place on a balancedsurface andgive time for excess
water to dry up
2. Check for any holesor cracks onthe tank
3. Seal the drain properlyand do not over tighten
4. Check for cracksor damages of the water inlet flap
5. Drain some waterand do not fill past High and check
that the internal floatis properly positioned
6. Open unit from theback and check the pipes for any
leaks and disconnections
7. Remove and properlyclean the cooling pads
8. Tuck the side opening under and into the bracket
9. foam product been used clean the cooling pads
Making noise1. Fan blades aredirty,warped, or
broken
2. Replace the motor
Build-up is blockingthe airflow
3.
Waterwas filled toohigh and
reached the fanblades
4.
1. Replace the fan blade
2. Replace the motor
Clean the unit fromthe inside out and all of the
cooling pads and screens
3.
Drain some water andallow for drying
4.
No wind supplyor the
airflow is too low
1. Cooling padsor screens areclogged
2. Control panelis broken
3. Remote controlis broken
4. Fan is not turningon
5. Shortage in thephase wire
1. Clean or replace thecooling pads or screens
2. Replace the controlpanel
3. Check batteries or replacethe remote
4. Check the motorfrom inside ofthe unit
5. Check the phasewire
No Cooling1. Shortage of waterin the reservoir
2. Water pumpbroken
3. “Cooling” buttonon the panel is
broken or turned off
4. Remote controlbroken
1. Add water to reservoirand makesure “snowflake”
stayslit up on controlpanel
2. Repair the water pump
3. Check the panel and/orreplace
4. Check the batteries orreplace remote
Waterreservoir or
screens have white
build up
1. Mineral substancein the water is
too high
2. Improper chemicalswere added
to the unit
1. Clean more frequently
2. Do not add anychemical to the water or to the unit
4. Power strip is too strong or
too weak
4. Use a proper outlet for machine
9. spitting water
6. Plug unit into a proper plug with more voltage
6. Outlet is too weak for amperage
5. pump sensor
5. Check the pump sensor if its floating
To Next Page
Loading...
