California Instruments 801RP Series User Manual

85 pages

To Next Page

Revision P

October 2005

by California Instruments.

P/N 5003-960

801RP / 1251RP Series AC Power

Source

User and Programming Manual

TEL: +1 (858) 677-9040

FAX: +1 (858) 677-0940

Email:

sales@calinst.com

Web Site:

http://www.calinst.com

Table of Contents5
Introduction8
General Description8
Specifications9
Electrical9
Mechanical12
Environmental13
Regulatory13
Front Panel Controls14
Available Options14
Unpacking and Installation15
Unpacking15
Power Requirements15
Mechanical Installation15
Figure 3-1: the 801RP/1251RP AC Power Source15
Input Wiring16
Output Connections16
Figure 3-2: Rear Panel View16
Output Voltage Ranges17
Functional Test17
Figure 3-3: Functional Test Setup18
Front Panel Operation19
Front Panel Guided Tour19
Figure 4-1: Front Panel View19
Figure 4-2: Shuttle Knob21
How to23
Principle of Operation26
General26
Overall Description26
Power Factor Correction Module (PFC)26
Figure 5-1: AC Source Block Diagram26
DC - DC Converter Module27
Table 1: Logic Board Led's27
Oscillator Control Board28
Figure 5-2: Oscillator and Controls28
DC to AC Power Module29
Ieee 488/ Rs23229
Calibration31
Calibration Equipment31
Routine Calibration31
Table 2: Load and Current31
Figure 6-1: Test Equipment Hookup for Routine Output Calibration32
Figure 6-2: Test Equipment Hook-Up for Measurement Calibration33
Non-Routine Calibration34
Figure 6-3: Location of Internal Adjustments35
Service36
General36
Basic Operation36
Table 3: Basic Symptoms36
Table 4: Poor Output Voltage Regulation36
Table 5: Overload Light on36
Table 6: Distorted Output37
Table 7: Unit Shuts down after 3-5 Seconds37
Table 8: no Output and no Lights on Front Panel37
Table 9: no Output but "Power On" Led Is Lit37
Advanced Troubleshooting38
Introduction to PGUI3241
About this Program41
About this Section of the Manual41
Program Requirements41
RS232C Cable Wiring42
Figure 8-1: RS232C Cable Wiring42
PGUI32 Setup and Installation43
Connecting the AC Source to the PC When Using RS23243
Connecting the AC Source to the PC Using IEEE-48843
Installing the PGUI32 Software43
Trouble Shooting - RS232C44
Figure 9-1: System Properties Dialog Box45
Figure 9-2: Advanced Port Settings Dialog Box45
Registration46
Figure 9-3: COM Port Properties Dialog Box46
Top Assembly Replaceable Parts47
Table 10: Replaceable Parts47
Programming Information48
Introduction to SCPI50
Conventions Used in this Manual50
The SCPI Commands and Messages50
Figure 12-1: Partial Command Tree51
Using Queries52
Structure of a SCPI Message53
Figure 12-2: Command Message Structure53
SCPI Data Formats55
System Considerations57
IEEE Interface57
RS232C Interface57
Figure 13-1: GPIB Address Selection Switch57
Figure 13-2: RS232C Interface Cable Wiring Diagram59
SCPI Command Reference60
Introduction60
Subsystem Commands60
System Commands67
Common Commands70
Table 11: Bit Configuration of Standard Event Status Enable Register71
Table 12: Bit Configuration of Standard Event Status Register72
Table 13: *RST Default Parameter Values74
Table 14: Status Register Power on Condition74
Table 15: Bit Configuration of Status Byte Register75
Programming Examples76
Introduction76
Programming the Output76
Making Measurements77
Status Registers78
Power-On Conditions78
Figure 16-1: AC Source Status System Model78
Standard Event Status Group79
Status Byte Register79
Examples80
Table 16: Error Messages83
Index84

Need help?

Do you have a question about the California Instruments 801RP Series and is the answer not in the manual?

California Instruments 801RP Series Specifications

General

Brand	California Instruments
Model	801RP Series
Category	Power Supply
Language	English

Related product manuals

2750L-P Series

151 pages

California Instruments 801RP Series User Manual

Table of Contents

California Instruments 801RP Series Specifications

Related product manuals