Why does my Canon XF300 not turn on?
Your Canon Camcorder might not be turning on because the battery pack is exhausted. Try replacing or charging the battery pack. Also, try removing the battery pack and reattaching it correctly.
Why does changing between recording and record pause take long on Canon Camcorder?
If changing between recording (NREC) and record pause (STBY) on your Canon Camcorder takes longer than usual, it could be due to a large number of clips on the CF card. Save your clips and initialize the CF card, or replace it.
Why my Canon XF300 cannot record to a CF card properly?
If your Canon Camcorder cannot record to a CF card properly, it may occur as recordings are made and deleted over time. Try saving your clips and initializing the CF card.
Why does my Canon Camcorder get hot after using it for a long time?
If your Canon Camcorder gets hot after extended use, it's normal. However, if it becomes unusually hot or heats up quickly, it may indicate a problem. In this case, consult a Canon Service Center.
Why does deleting clips take longer than usual on Canon XF300?
If deleting clips on your Canon Camcorder is taking longer than usual, it could be because the CF card contains many clips. Save your clips and initialize the CF card.
What does 'CF A/CF B Cannot restore' mean on Canon XF300?
If your Canon Camcorder displays 'CF A/CF B Cannot restore', it indicates that the data on the CF card could not be recovered. Save your clips and initialize the CF card.
Why can't I switch CF card slots on my Canon XF300?
If your Canon Camcorder cannot switch CF card slots, it's likely because you pressed the SLOT SELECT button while recording. Wait until recording is finished before changing the selected CF card slot.
Why my Canon XF300 cannot play back?
If your Canon Camcorder cannot play back, the file control information might be corrupted, or there was a decoder error. Turn the camcorder off and on again. If the problem persists, consult a Canon Service Center. Note that CF cards or clips with corrupt file control information cannot be read by the supplied Canon XF Utility or plugins.
Why my Canon XF300 Camcorder cannot record?
If your Canon Camcorder cannot record, the file control information might be corrupted, or there was an encoder error. Turn the camcorder off and on again, then remove and reinsert the CF card or replace it. If the problem continues, consult a Canon Service Center. Note that CF cards or clips with corrupt file control information cannot be read by the supplied Canon XF Utility or plugins.
General| Filter size | 82 mm |
|---|---|
| Digital zoom | 1.5 x |
| Optical zoom | 18 x |
| Image stabilizer | Yes |
| Focal length range | 4.1 - 73.8 mm |
| Focal length (35mm film equivalent) | 29.3 - 527.4 mm |
| Sensor type | CMOS |
| Total megapixels | 2.37 MP |
| Optical sensor size | 1/3 \ |
| Video out | 1 |
| Flash memory | 32768 MB |
| Aperture range (F-F) | 1.6 - 22 |
| Horizontal resolution | 1000 lines |
| Power consumption (typical) | 9 W |
| Viewfinder resolution | 1550000 pixels |
| Viewfinder screen size | 0.57 \ |
| Display diagonal | 4 \ |
| ISO sensitivity | Auto |
| Normal focusing range | 0.02 - 1 m |
| Maximum frame rate | 50 fps |
| Maximum video resolution | 1920 x 1080 pixels |
| Image formats supported | JPG |
| Audio formats supported | MP3 |
| Camera shutter speed | 1/18 - 1/2000 s |
| Microphone in | No |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Firewire (IEEE 1394) ports | 0 |
| Compatible memory cards | SD, SDHC |
| Product color | Black |
| Video recording time | 1.2 h |
| Operating temperature (T-T) | -5 - 45 °C |
Weight and Dimensions| Depth | 180 mm |
|---|---|
| Width | 394 mm |
| Height | 192 mm |
| Weight | 2700 g |
To Next Page
