What does a Line Isolation Monitor (LIM) alarm or error mean on CardioQuip Medical Equipment?
If you receive a Line Isolation Monitor (LIM) alarm or error on your CardioQuip Medical Equipment, contact the LIM vendor if the LIM is not rated for the power requirements and/or power factor of the MCH. If the LIM is properly rated, contact CardioQuip Service, as the issue may be due to excessive leakage current from the MCH.
What to do if there is no circulation on main water connections in CardioQuip Temperature Controller?
If there is no circulation on the main water connections of the CardioQuip Temperature Controller, first ensure the system is in RUN mode to activate the pump. Check that the Internal Recirculation Valve is set to the NORMAL position. Also, inspect the water tank for blockages by cleaning the mesh strainers at the bottom of the tank with a nylon brush. Examine the external tubing for any closed valves, kinks, bends, or other obstructions. Other possible causes include a pump wiring fault, or a faulty pump or pump circuitry.
What to do if CardioQuip Temperature Controller system water flow is inadequate?
If the CardioQuip Temperature Controller system water flow is inadequate, place the system in PRIMING mode according to the operating instructions. Additionally, clean the mesh strainers at the bottom of the water tank with a nylon brush to remove any blockages. A blockage in the plumbing circuit may also be the cause, so have qualified service personnel inspect the internal tubing for kinks, bends, or other blockages. Another possible cause is a faulty pump or pump circuitry.
Why is my CardioQuip Temperature Controller system not cooling?
If the CardioQuip Temperature Controller system will not cool, ensure there is an adequate supply of ice in the water tank, using ice made from sterile or 0.22-micron filtered water. Also, check if the water flow is inadequate. Finally, check if there is no water flow at the main water output.
What causes a CardioQuip Temperature Controller system to not heat?
If the CardioQuip Temperature Controller system will not heat, have qualified service personnel inspect the internal tubing for kinks, bends, or other blockages. Additionally, have them check for an open in the Heater input wiring. Another possible cause is a faulty heater or heater circuitry.
Why doesn't water flow through the cold water tank in CardioQuip MCH-1000 Medical Equipment?
If water does not flow through the cold water tank of your CardioQuip Medical Equipment, have qualified service personnel inspect the internal tubing for kinks, bends, or other blockage, as this could indicate a blockage in the plumbing circuit. Additionally, they should check for an open in the valve input wiring to ensure internal wiring continuity and inspect and lubricate the valve solenoid to address potential valve solenoid seizure. For a faulty valve or valve circuitry, contact CardioQuip Service.
What to do if CardioQuip Medical Equipment's touchscreen display is off but the main power switch lights up?
If the main power switch lights up, but the touchscreen display is off and the CardioQuip Medical Equipment system will not operate, have qualified service personnel inspect the internal wiring for disconnected plugs or loose wire connections, as this could be due to a disconnected DC Power Supply, or other loose internal wiring. If the wiring is intact, the issue may be a faulty DC Power Supply, in which case you should contact CardioQuip Service.
What causes CardioQuip MCH-1000 Medical Equipment to go into an overtemperature condition?
If your CardioQuip Medical Equipment system goes into an overtemperature condition, have qualified service personnel inspect the internal tubing for kinks, bends, or other blockage. It could also be caused by faulty temperature control circuitry or a faulty heater or heater circuitry, in which case you should contact CardioQuip Service.
Why are the hoses on my CardioQuip Temperature Controller cloudy or discolored?
If the hoses of the CardioQuip Temperature Controller are cloudy or discolored, immediately remove the device from service and contact CardioQuip Customer Service regarding servicing assistance, as the device may be contaminated or the exterior tubing may have undergone physical changes.
Why won't my CardioQuip Temperature Controller system operate, even though the touchscreen display is on?
If the CardioQuip Temperature Controller system will not operate, but the touchscreen display is on, have qualified service personnel check for an open in the DC Power Supply input wiring.
Covers low water level and low ice alarms, detailing priority and silencing.
Explains the large dripless connectors for arterial/cardioplegia heat exchangers.
Explains how to test the temperature control system's accuracy and response.
Guides the user through testing various alarm functions of the MCH.
Covers water quality requirements and approved cleaners/disinfectants.
Addresses problems like failure to turn on, unresponsive display, and circulation issues.
Displays the detailed wiring schematic for the MCH-1000(i) model.
General| Brand | CardioQuip |
|---|---|
| Model | MCH-1000 |
| Category | Medical Equipment |
| Language | English |
To Next Page