CareFusion Bird Sentry

Questions and Answers

E
Emily OconnorAug 16, 2025
Why is there an oxygen concentration discrepancy on my CareFusion Bird Sentry?
- K
  Kendra SmithAug 17, 2025
  A discrepancy between the oxygen concentration selection knob and the actual reading on the display of your CareFusion Blender can occur for several reasons: * The monitor may be out of calibration, requiring recalibration. * The sensor might be exhausted and needs replacement. * Outlet flows might be below the specified range and should be corrected to above 2 LPM. * The gas supply could be contaminated, or the Bird Sentry blender operation may be out of calibration, in which case you should contact CareFusion Corporation or a distributor for repair.
A
Andrew AndersonAug 19, 2025
What to do if the pressure differential alarm is sounding on my CareFusion Bird Sentry?
- U
  ucrosbyAug 19, 2025
  If the pressure differential alarm is sounding on your CareFusion Blender, it could be due to: * Inlet pressure differences of 20 PSI or more, which requires correcting the pressure difference. * The pressure alarm not being calibrated properly, or the Bird Sentry blender operation being out of calibration, in which case you should contact a CareFusion distributor or CareFusion Corporation for repair.
S
Sandra JohnsonAug 22, 2025
What to do if the sensor will calibrate, but takes too long to return to 21% ±2% oxygen in air when performing the daily check procedure on CareFusion Bird Sentry?
- M
  Mitchell JonesAug 22, 2025
  If the sensor on your CareFusion Blender calibrates but takes too long to return to 21% ±2% oxygen in air during the daily check, the disposable oxygen sensor might be damaged or defective and needs replacement. Refer to Ch. 6, Service and Maintenance, Disposable Galvanic O Sensor 2 Cable.
S
Sarah FowlerAug 25, 2025
What to do if the sensor will calibrate, but does not return to 21% ±2% oxygen in air when performing daily check procedure on CareFusion Bird Sentry Blender?
- T
  territaylorAug 26, 2025
  If the sensor of your CareFusion Blender calibrates but does not return to 21% ±2% oxygen in air when performing the daily check procedure, the disposable oxygen sensor may be damaged or defective and needs to be replaced.
N
nedwardsAug 27, 2025
How to fix a blank display on CareFusion Bird Sentry?
- A
  austinhoustonAug 27, 2025
  A blank display on your CareFusion Blender might be due to: * The battery not being installed, which requires installing it according to Appendix C, Setup and Installation, Battery Installation. * The battery being completely dead, necessitating replacement as described in Appendix C, Setup and Installation, Battery Installation. * The monitor being defective, in which case you should contact a CareFusion distributor or CareFusion Corporation for repair.
S
Sandra PerezAug 30, 2025
What causes inaccurate oxygen concentration when gas pressures are equal in CareFusion Bird Sentry?
- D
  ddanielAug 30, 2025
  If the selected oxygen concentration is accurate only when gas pressures are equal in your CareFusion Blender, the Bird Sentry blender balance module may not be functioning properly. Contact a CareFusion distributor or CareFusion Corporation for repair.
X
xgoodwinSep 2, 2025
What to do if the sensor will not calibrate on CareFusion Blender?
- Z
  Zachary GainesSep 2, 2025
  If the sensor on your CareFusion Blender will not calibrate, it could be due to: * An exhausted sensor cell, requiring replacement. Refer to Ch. 6, Service and Maintenance. * A defective sensor cable or holder, in which case return it to CareFusion Corporation. * A defective monitor, which requires contacting a CareFusion distributor or CareFusion Corporation for repair.
W
wmilesSep 5, 2025
What to do if CareFusion Bird Sentry Blender is in bypass mode with no alarm?
- J
  Jillian HickmanSep 5, 2025
  If your Bird Sentry blender is in bypass mode with no audible pressure differential alarm, the reed alarm cap might be damaged or defective. Contact a CareFusion distributor or CareFusion Corporation for repair.
D
David EdwardsSep 7, 2025
What causes a partial or distorted display on CareFusion Bird Sentry Blender?
- J
  Jeremy HensonSep 7, 2025
  A partial or distorted display on your CareFusion Blender is likely due to a damaged monitor. Contact a CareFusion distributor or CareFusion Corporation for repair.
C
catherinechristianSep 10, 2025
What causes the sensor to drift more than ±3% over 24 hours on CareFusion Bird Sentry Blender?
- S
  sandra88Sep 10, 2025
  If the sensor on your CareFusion Blender calibrates, but the reading at any constant level drifts more than ±3% over a 24-hour period, it could be due to: * Barometric pressure change since the last calibration, requiring recalibration. * The room or gas temperature dropping below 59°F (15°C) or rising above 104°F (40°C), requiring temperature correction and recalibration.