What causes excessive section pressure in a Carrier 38QH36-H?
Excessive section pressure in your Carrier Air Conditioner can be caused by a reversing valve that is stuck or has an internal leak, in which case it should be replaced. Another cause could be an internal pressure relief valve that is open; check for the source and eliminate it. Overcharging the refrigerant can also lead to this issue; purge any excess refrigerant.
Why is my Carrier 38QH36-H not supplying enough heating?
If your Carrier Air Conditioner isn't heating adequately, several factors could be responsible. Ensure that the airflow isn't blocked by any obstructions. Clean the air filters, as dirty filters reduce air circulation. Confirm that all doors and windows are closed. Increase the fan speed if it's set to “Low”. Adjust the airflow direction according to the chosen mode. Finally, verify that the selected temperature is not lower than the room temperature when in heating mode, and correct it if needed.
What to do if my Carrier 38QH36-H Air Conditioner remote control does not acknowledge signal with a beep when pressing any function button?
If your Carrier Air Conditioner doesn't respond to the remote, even when the remote display shows the function, try these steps: First, ensure the main switch of the unit is in the ON position. Then, replace the remote control batteries. Make sure you're pointing the remote directly at the indoor unit's receiver. Remove any obstacles like curtains or walls that might be blocking the signal. Also, avoid direct sunlight on the receiver. Finally, be aware that electromagnetic interference from nearby devices like computers or appliances can obstruct the signal.
What to do if my Carrier 38QH36-H Air Conditioner does not acknowledge signal with a beep when pressing start button?
If your Carrier Air Conditioner isn't responding to the start button on the remote, consider these possibilities: Ensure the main switch is in the ON position. Replace the remote's batteries. Point the remote directly at the indoor unit's receiver, making sure there are no obstructions like curtains or walls. Also, avoid direct sunlight on the receiver. Electromagnetic interference from nearby appliances might also be a factor, so avoid sending signals when computers or household appliances are operating close by.
What to do if my Carrier Air Conditioner does not acknowledge signal with a beep when pressing stop button?
If your Carrier Air Conditioner isn't responding when you press the stop button on the remote, try these solutions: Replace the remote's batteries. Ensure you are pointing the remote directly at the indoor unit's receiver, without any obstacles like curtains or walls in the way. Avoid direct sunlight on the receiver. Also, be aware that electromagnetic interference from nearby devices could be interfering with the signal.
What to do if the display is not lit after placing batteries into the remote control of my Carrier 38QH36-H?
If the display on your Carrier Air Conditioner remote control isn't lit after inserting batteries, the batteries may be exhausted or have the wrong polarity. Replace the batteries or check their polarity.
Why did the outdoor fan stop or cycle on overload on my Carrier Air Conditioner?
If the outdoor fan on your Carrier Air Conditioner has stopped or is cycling on overload, it could be due to a defective fan motor capacitor, which would need replacement. Loose leads at the fan motor can also cause this issue; check for the cause and eliminate it. Other potential causes include a burned-out fan motor (replace it) or a seized motor bearing (check for the cause and eliminate it).
What causes low head pressure in a Carrier 38QH36-H Air Conditioner?
Low head pressure in your Carrier Air Conditioner can be due to a low refrigerant charge. In this case, check for leaks, repair them, and recharge the system. A restriction in the liquid tube can also cause this; remove the restriction. Additionally, a dirty indoor section air filter can be the culprit; clear the filter.
Why is the Power LED blinking on my Carrier 38QH36-H Air Conditioner?
If the power LED is blinking on your Carrier Air Conditioner, it could be due to compressor overheat, anti-overheat protection being active, or low ambient temperature. Determine the reason and correct the issue.
Why does my Carrier 38QH36-H indoor unit have unpleasant smells?
Unpleasant smells from your Carrier Air Conditioner's indoor unit can be caused by substances accumulated in the air filters. Switch the system OFF and contact an authorized service center to have the filters cleaned. Restart unit in the ventilation (fan only) mode and open windows to change room air.
General| Heating Seasonal Performance Factor (HSPF) | 9.0 |
|---|---|
| Phase | 1 |
| Cooling Capacity | 36000 BTU/h |
| Heating Capacity | 36000 BTU/h |
| Seasonal Energy Efficiency Ratio (SEER) | 16.0 |
| Refrigerant | R410A |
| Voltage | 208/230V |
| Sound Pressure Level (Indoor) | 42 dB |
Service and maintenance can be hazardous; only trained personnel should perform.
Details what is not covered in Carrier warranty, including misuse and improper maintenance.
Nominal voltage, minimum, and maximum voltage for the unit.
Lists protection types, effects, modes, and conditions for heat pump systems.
Lists protection types, effects, modes, and conditions for cool-only systems.
Explains defrost cycles in heat pump mode and indoor fan behavior.
Wiring diagram for the indoor unit of the heat pump model.
Wiring diagram for the indoor unit of the cool-only model.
Wiring diagram for the outdoor unit of the heat pump model.
Reasons and actions for when the compressor and outdoor fan fail to start.
Troubleshooting for compressor not starting, cycling, or operating continuously.
Reasons and actions for excessive head pressure and compressor overload cycles.
Troubleshooting for low head pressure, excessive/low suction pressure.
Reasons and actions for insufficient cooling or heating.
Reasons and actions for blinking Timer or Power LEDs.
To Next Page