Carrier 48LJE004 - Page 6

O'-* 15/16"
11251
_r-5 \/r_
[4441
SUPPLY*AIR
1; OPENING
I* (HORIZONTAL)
*X- -
0' -7 1/2'
[1913
£'-10 5/6"
C270] 1
I RETURN- I
t AIR ,
•I OPENING I
(HORIZONTAL)
i;
I* -B 3/16 |
I [1573 I 1
0'-4 1/4'
‘[1083
_ FILTER ACCESS PANEL
[THROWAWAY FILTERS)
OPTIONAL
OUTDOOR AIR HOOD
AND FILTERS
l'-7 3/4"
OUTDOOR AIR t5 ? 23
48LJE/LJF004
48LJD/LJE/LJF005
48LJD/LJE/LJF006
L0'-4 11/16'
[1193
ESTO CX3NO048A1EORAM
RIGHT SIDE
48UD/LJE/LJF007 615
48LJE/LJF004
48 L J D/L J E/L J F005
48LJD/LJE/LJF006
48L J D/LJ E/L J FOOT
STD UNIT ECONOMIZER
WEIGHT WEIGHT
Kg
15.4
15.4
560 254 34 15 4
615 279 34 15 4
CORNER CORNER
WEIGHT (A) WEIGHT (B)
CORNER
WEIGHT (C)
Lb
Kg
159
72.1
162
73.5
168
76.2
185
83.9
CORNER
WEIGHT (D)
'Indicates horizontal center of gravity
-{•Indicates vertical center of gravity
NOTES:
1. Dimensions in [ ] are in millimeters.
Center of Gravity.
3 Direction of airflow
4. On vertical discharge units, ductwork is to be
attached to accessory roof curb only. For hor¬
izontal discharge units, field-supplied flanges
should be attached to horizontal discharge
openings and all ductwork should be at¬
tached to the flanges.
5 Minimum clearances are as follows (local codes
or jurisdiction may prevail):
NOTE: When installing these units, use the
maximum clearance stated for your application
a Between unit, flue side, and combustible
surfaces, 36 inches. (Minimum clearance
to combustibles, flue side, is 18 in for units
with accessory flue discharge deflector.)
b. Bottom to combustible surfaces (when not
using curb), 0 in. for LJD,LJE units and
1 in. for LJF units.
c. Condenser coil for proper airflow, 36-in one
side, 12 in the other The side getting the
greater clearance is optional
d. Overhead, 60 in to assure proper con¬
denser fan operation
e. Horizontal supply and return end, 0 inches
f Between units, control box side, 42 in per
NEC (National Electrical Code),
g Between unit and ungrounded surfaces, con¬
trol box side, 36 in. per NEC.
h. Between unit and block or concrete walls
and other grounded surfaces, control box
side, 42 in. per NEC.
6. With the exception of the clearance for the
condenser coil and combustion side, as stated
in Notes 5a, b, and c, a removable fence or
barricade requires no clearance
7 Units may be installed on combustible floors
made from wood or class A, B, or C roof cov¬
ering material
filter/economizer access panel-
i—CONDENSER COIL
0‘-2 15/16'-
[7S3
O'-4 1/2’
[11431
£ [6333 ’
T-4 3/8"
(4163
0 -3 3/1B"j_—CORNER "B"
‘[813
I V/ O'-S 7/16'
L [1383
EVAPORATOR
COIL ,
RETURN-AIR OPENING
(VERTICAL I
*
6'-! 11/16"
[18723
MOUNT
(XS00AM6CT
HERE
t 1’-2 1/4 1
rr i 362 !
FRONT
2 '-e i/ 2 " |
(8263 2' -O"
I [6101
' B FLUE mooo
/
1'-4 5/16'
(41 S3
SUPPLY-AIR
1 OPENING
| (VERTICAL) I
0'-10 15/16
(2783
’ (AS?) 4 " SUPPLY * IH
O'-S 7/16'
(1381
r-0 1/lfiJ L-0'-3 3/16''""' CORNER "c
[3063 f (813
_ Connection Sizes _
1 3 /s" Dia [35] Field Power Supply Hole
2" Dia [50.5] Power Supply Knockout
2 3 /i6" Dia [551 Charging-Port Hole
Vs" [22] Field Control Wiring Hole
3 /4" Condensate Drain _
V2"-14 NPT Gas Connection
O'-O 3/8'
■ ( 10 )
EVAPORATOR-FAN MOTOR AND
BLOWER ACCESS PANS.
3'-S 3/16
“ Cl 04 63
LEFT SIDE
Fig. 6 — Base Unit Dimensions
0'-5 13/16
[1473 2 1/4-|58]
(TYP 8 PLACES)
FRONT
6