CAS Corporation ER PLUS Series

Need help?

Do you have a question about the CAS Corporation ER PLUS Series and is the answer not in the manual?

Summary

1. Introduction and Precautions

1.1. Preface

Expresses gratitude for purchase and highlights scale quality and performance.

1.2. Precautions

Lists essential safety precautions for operating and maintaining the scale.

1.3. Specifications

1.3.1. Kilogram (kg) Version

Outlines specifications for ERPLUS models operating in kilograms.

1.3.2. Pound (lb) Version

Outlines specifications for ERPLUS models operating in pounds.

1.4-1.8. ERPLUS and ERPLUS-M Versions

1.4. ERPLUS LCD Version

Details specifications specific to the ERPLUS LCD model.

1.5. ERPLUS VFD Version

Details specifications specific to the ERPLUS VFD model.

1.6. ERPLUS LED Version

Details specifications specific to the ERPLUS LED model.

1.7. ERPLUS-M LCD Version

Details specifications specific to the ERPLUS-M LCD model.

1.8. ERPLUS-M LED Version

Details specifications specific to the ERPLUS-M LED model.

1.9. Dimensions

1.10. Sealing Method

2. Calibration

2.1. General Calibration

Describes the general steps to enter and navigate calibration modes.

2.1.1. C4 Setting

Details how to configure optional settings using hexadecimal numbers in the C-4 menu.

2.1.2. SPAN Calibration Setting (C-3)

Guides through the 3-point span calibration process.

2.1.3. Gravity Constant Value Setting (C-9)

Explains how to set the gravity constant for accurate weighing.

2.1.4. Calibration factor Setting (C-10)

Details setting calibration factors like unit, capacity, and division.

2.1.5. Displaying Raw A;D Value (C-5)

Describes how to view raw A/D values to check load cell status.

2.1.6. Allocate Function Key Codes to Changeable keys (C-6)

Explains how to assign functions to keys using soft key codes.

2.1.7. Percent Calibration (C-7)

Details the procedure for performing percent calibration.

2.1.8. Battery Calibration (C-8)

Outlines the steps for calibrating the scale's battery.

3. The Schematics and Diagram

3.1. System Block Diagram

Presents a block diagram illustrating the system architecture.

4. Exploded View

5. Load Cell drawing

6. Part Location

6.1. ERPLUS LCD Version Part Locations

Component locations for ERPLUS LCD version PCBs.

6.1.2. ERPLUS VFD Version Part Locations

Component locations for ERPLUS VFD version PCBs.

6.1.3. ERPLUS LED Version Part Locations

Component locations for ERPLUS LED version PCBs.

6.1.4. ERPLUS-M LCD Version Part Locations

Component locations for ERPLUS-M LCD version PCBs.

6.1.5. ERPLUS-M LED Version Part Locations

Component locations for ERPLUS-M LED version PCBs.

6.1.6. Common PCB Part Locations

Component locations for common PCBs.

7. Error Messages & Solution

8. Part List

8.1. Main PCB Assembly Parts (LCD)

Parts for ERPLUS LCD main PCB assembly.

8.2. Front & Rear Display PCB Parts (LCD)

Parts for ERPLUS LCD front and rear display PCBs.

8.3. Key & RS232 C PCB Parts (LCD)

Parts for ERPLUS LCD key and RS232C PCBs.

8.1. Main PCB Assembly Parts (LED)

Parts for ERPLUS LED main PCB assembly.

8.2. Display PCB Parts (LED)

Parts for ERPLUS LED display PCBs.

8.3. Key & RS232 C PCB Parts (VFD)

Parts for ERPLUS VFD key and RS232C PCBs.

8.1. Main PCB Assembly Parts (VFD)

Parts for ERPLUS VFD main PCB assembly.

8.2. Front & Rear Display PCB Parts (VFD)

Parts for ERPLUS VFD front and rear display PCBs.

8.1. Main PCB Assembly Parts (ERPLUS-M LCD)

Parts for ERPLUS-M LCD main PCB assembly.

8.2. Display PCB Parts (ERPLUS-M LCD)

Parts for ERPLUS-M LCD display PCBs.

8.1. Main PCB Assembly Parts (ERPLUS-M LED)

Parts for ERPLUS-M LED main PCB assembly.

8.2. Display PCB Parts (ERPLUS-M LED)

Parts for ERPLUS-M LED display PCBs.

8.3. Key & RS232 C PCB Parts (ERPLUS-M VFD)

Parts for ERPLUS-M VFD key and RS232C PCBs.