Casanoov TANKER C600 - User Manual

Questions and Answers

K
Kevin MillsAug 6, 2025
Why my Casanoov TANKER C600 Gate Opener fails to operate?
- C
  Christian JacksonAug 6, 2025
  If your Casanoov Gate Opener fails to operate, first check the clutch states to ensure it's in a power-driven state. Check for power indications and tripped breakers; restore power if needed. Also, inspect the fuse and replace it if broken. The issue might stem from remote control failure, requiring detection or replacement. Damaged power cables, or remote control and motor problems also can cause the gate to fail, requiring detection and repair.
C
cindylaneAug 13, 2025
Why is the working distance of my Casanoov TANKER C600 Gate Opener remote control reduced?
- B
  Brandon MillerAug 13, 2025
  If the working distance of your Casanoov Gate Opener's remote control is reduced, it could be due to several reasons. First, check the battery power; a low or damaged battery should be replaced. Interference from other equipment using the same frequency can also cause this issue; wait or eliminate the interference. Finally, the receiver of the controller might be damaged, necessitating replacement of the control board.
K
Kathleen SandersAug 20, 2025
What to do if Casanoov Gate Opener fails to stop at start or end position?
- T
  thaynesAug 20, 2025
  If your Casanoov Gate Opener fails to stop at the start or end position, it may be due to a damaged or obstructed terminal stop toggle switch; replace the switch or remove any obstructions. Also, check the limit switch of the motor and the limit detection of the interface PCB board to ensure they are properly inserted and fixed. The limit of open and close may be in the wrong position, requiring adjustment of the limit switch (K1).
K
Kristine SullivanAug 27, 2025
How to fix Casanoov TANKER C600 Gate Opener when it won't work after pressing open/close key?
- B
  baileychristopherAug 27, 2025
  If pressing the open and close key of your Casanoov Gate Opener motor does not result in operation, it could be due to a couple of reasons. The blocked sensitivity might be set too high; lower the blocked sensitivity and ensure the gears and racks can operate normally. Alternatively, the gate might have lifted off the track, disengaging the drive gear from the rack, which requires maintenance and replacement.

Summary

General Safety Warning

Safety Precautions

Installation and Maintenance Safety

Product must be installed by trained personnel; disconnect power before maintenance.

Operational Safety

Read manual carefully; replace damaged cables properly to avoid shock.

User Safety

Keep transmitters out of reach; do not allow children near moving gates.

Environmental Considerations

Do not install in corrosive, inflammable, or explosive environments.

Tools and Components Required

Required Tools

Essential tools for installation including drill, screwdriver, pliers, level, and wrenches.

Included Components

List of included gate opener components: motors, remote controls, photocells, etc.

Product Identification and Specifications

Product SKU and Name

Identifies the product SKU and its name as an automatic sliding gate opener.

Technical Label Information

Label showing voltage, power, IP rating, nominal force, and origin country.

Product Overview and Technical Data

Dimensional Overview

Illustrates the physical dimensions of the gate opener from different angles.

Detailed Technical Specifications

Details technical parameters including voltage, power, speed, weight, and operating conditions.

Gate Automation Features

System Components Identification

Diagram identifying main system components like alarm lamp, photocell, and gate motor.

Manual Unlocking Procedure

Step-by-step guide on how to perform manual unlocking of the gate motor.

General Features and Installation Preparation

Key Product Features

Highlights features such as stylish design, built-in control panel, and durable metal gears.

Base Plate Installation

Instructions for fixing the base plate using bolts and determining motor position.

Rack and Limit Magnet Installation

Rack Installation Steps

Steps for setting the gear-motor and fixing the rack to the gate, ensuring proper spacing.

Limit Magnet Setup

Procedure for installing limit magnets to define gate open and close positions correctly.

Control Board Configuration

Control Board Layout

Diagram labeling components and terminals on the EGB-02 control board.

Wiring Diagrams

Shows wiring diagrams for connecting the motor, photocells, and alarm lamp to the control board.

Motor Installation for Right Opening

Right Opening Configuration

Illustrates motor installation for right-side gate opening, noting factory setting.

Right Opening Wiring

Wiring details specific to the right-side gate opening configuration.

Motor Installation for Left Opening

Left Opening Diagram

Diagram and notes for left-side gate opening, including wiring and J1 option.

Wire Exchange Caution

Important note regarding wire exchange and J1 cap adjustment for proper motor function.

Electrical Connection Details

Flashing Light Connection

Diagram showing the connection of the flashing light to the control board terminals.

Infra-red Photocell Wiring

Wiring diagram for connecting infra-red photocells to the control board.

Function Testing and Adjustments

Terminal Stop Detection Test

Explains testing of terminal stop detection for gate limit control.

Power Switch and Limit Switch Options

Covers the power switch function and limit switch options (J1).

Programming and Learning Features

Details programming settings, learning button function, and sensitivity adjustments.

Gate Operation Logic

Sensitivity Adjustments Explained

Explains high and low sensitivity settings for detecting gate obstructions.

Programming Settings Overview

Overview of the 8 programmable settings available on the control board.

Limit Modes and Infrared Settings

Details optional limit modes (NC/NO) and infrared mode settings.

Advanced Settings and Remote Control

Auto-Close and Pedestrian Mode

Configures auto-close timing when pedestrian mode is activated by remote.

Condominium and Button Modes

Details condominium mode activation and remote control button configurations.

Remote Control Code Management

Instructions for learning new remote controls and clearing existing codes from the control board.

Capacitor and Switch Configurations

Motor-Start Capacitor Connection

Instructions for connecting and securing motor-start capacitors to the control board.

Limited Switch Option Functionality

Details the function of limited switch options (J1) for gate direction detection.

Stop Detection and Power Switch Usage

Explains terminal stop detection interface and the power switch functionality.

Troubleshooting Guide

Gate Operation Faults

Addresses common problems like gate failure to operate, reduced remote range, or stopping errors.

Manual Operation Faults

Covers issues when pressing open/close keys, such as motor not working or operating.

Important Operational Notes

Key safety and operational notes, including fuse rating, electricity precautions, and gear alignment.

DIP Switch Settings

Limit & Infrared DIP Settings

Details DIP switch settings for limit modes (NC/NO) and infrared.

Auto-Close & Pedestrian DIP Settings

Configuration of DIP switches for auto-close timing and pedestrian mode activation.

Condominium & Button DIP Settings

DIP switch settings for condominium mode and remote button control modes.

Flash Lamp Information

Flash Lamp Safety Warning

Safety instructions for the flash lamp, emphasizing manual reading and power safety.

Flash Lamp Specifications

Technical specifications for the flash lamp, including voltage, capacity, frequency, temperature, and IP level.

CE Conformity Declaration

Manufacturer Declaration

Manufacturer's declaration of product compliance with CE directives and standards.

Key Technical Characteristics

Summary of main technical characteristics such as voltage, power, speed, and protection class.

Casanoov TANKER C600 Specifications

General

Type	Sliding Gate Opener
Max. Gate Weight	600 kg
Motor Power	280 W
Remote Control Distance	30 m
Motor Type	AC Motor
Power	280 W
Opening Speed	12 m/min
Protection Level	IP44
Control Type	Remote Control
Operating Temperature	-20°C to +50°C
Safety Features	Obstacle Detection

Related product manuals

Casanoov RANGER B150

154 pages