Casio 5143 User Manual

Operation Guide 5143
E-9
While crown button mode switching is disabled, pressing the crown button will x
cause the
x
Second Hand to move to the 3 o’clock position. The
x
Second Hand
will resume normal timekeeping when you release the crown button.
To re-enable crown button mode switching
Hold down the crown button as you press A.
E-8
Note
If you do not perform any operation for more than three minutes after pulling out the
x
crown, crown operations will become disabled automatically. If this happens, push
the crown back in and then pull it out again to re-enable crown operations.
Disabling Crown Button Mode Switching
You can use the following operation to disable crown button mode switching.
This helps to prevent accidental mode changes while wearing the watch.
To disable crown button mode switching
Hold down the crown button for at least two seconds until the watch beeps and 1.
then press A.
At this time the x
x
Second Hand will move to the 3 o’clock position.
Release both buttons.2.
The watch will return to normal timekeeping.
x
E-7
Note
You can use high-speed hand movement when confi guring time settings in the
x
Timekeeping Mode, Alarm Mode, or Countdown Timer Mode, or when adjusting the
home positions of the hands.
Pushing the Crown In
Carefully press the button of the crown the push the crown back in.
Important!
To prevent unintentional operation, the button press operation of the crown
x
becomes disabled automatically for about eight seconds after you push the crown
back in. It will become re-enabled after about eight seconds.
E-6
High-speed 1
With the crown pulled out, rotate it rapidly away from you two times.
High-speed 2
After starting the High-speed 1 operation, rotate the crown rapidly
away from you two more times.
High-speed Cancel
Rotate the crown towards you or press any button.
E-5
Pulling the Crown Out
After unlocking the crown, grasp the ring and pull the crown out.
Rotating the Crown
With the crown pulled out, grasp the ring and rotate the crown
towards you to move the hands of the watch.
You can also perform high-speed hand movement using the
operations described below. Note that there are two levels of high-
speed movement (High-speed 2 is faster).
Use High-speed 2 when changing the minute hand setting in the
x
Timekeeping Mode, Timer Mode, and Alarm Mode.
E-4
Note that rotating the ring without pushing it down as far as it will go will change the x
settings of the watch. When locking the crown, be sure to press down fi rmly on the
ring as you rotate it.
Unlocking the Crown
Rotate the ring part of the crown towards you until it loosens
completely.
Pressing the Crown Button
You can press the crown button while the crown is locked.
Crown ring
Press
E-3
Using the Crown
The crown of this watch has a button part and a ring part. You can use the crown’s
button and ring to perform a number of different crown operations.
Locking the Crown
To lock the crown, push down its ring part as far as it will go as you
rotate the ring away from you until it is relatively tight. While the
crown is locked correctly, the only crown operations possible are
pressing the crown button and unlocking the crown.
Important!
Push down on the ring as you slowly rotate it. You should be able to feel it screwing
x
securely into place.
You should normally have the crown locked during normal daily use. Leaving the x
crown unlocked creates the risk of unintended operations or even damage due to
impact.
E-2
About This Manual
In this manual, operations are performed using the watch’s
crown, and the three buttons indicated by the letters A,
B and C.
Hands and Indicators
z
Hour Hand
x
Second Hand
c
Minute Hand
v
Mode Disk: Rotates to indicate the current mode and
other information.
b
Chronograph Signal
n
Day
This User’s Guide uses numbers shown above to identify
watch hands and indicators.

+
6*>
@B
MA1203-EB
E-1
ENGLISH
Congratulations upon your selection of this CASIO watch.
Note that the product illustrations in this manual are intended for reference only,
x
and so the actual product may appear somewhat different than depicted by an
illustration.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.

Casio 5143 Specifications

General

Brand	Casio
Model	5143
Category	Watch
Language	English

Summary

About This Manual

Hands and Indicators

Identifies watch hands and indicators using numbers for reference.

Using the Crown

Locking the Crown

Instructions on how to lock the crown to prevent accidental operations.

Unlocking the Crown

Step-by-step guide to unlock the crown for normal operations.

Rotating the Crown

How to rotate the crown to adjust time and use high-speed hand movement.

Pushing the Crown In

Procedure for pushing the crown back in and its effect on operations.

Disabling Crown Button Mode Switching

How to Disable Mode Switching

Steps to prevent accidental mode changes using the crown button.

Re-enabling Mode Switching

Instructions to restore crown button mode switching functionality.

Things to check before using the watch

Charging the Watch

Charging Guide

Guidance on exposing the watch to light for optimal charging.

Power Levels

Understanding power levels via second hand movement and its implications.

Power Recovery Mode

Power Saving

Elapsed Time in Dark

How watch functions are affected when left in the dark.

To recover from the sleep state

Mode Reference Guide

Mode Pointer

Explanation of the mode pointer's function on the Mode Disk.

Split Pointer

Function of the split pointer in Stopwatch Split Mode.

Lap Pointer

Function of the lap pointer in Stopwatch Lap Mode.

Selecting a Mode

To determine the watch's current mode

How to identify the current mode using the Mode Disk.

To return to the Timekeeping Mode

Procedure to return to the Timekeeping Mode from any other mode.

Timekeeping

Configuring Home City Settings

To configure Home City settings

Steps to select a city code as Home City.

Daylight Saving Time (DST)

Explanation of Daylight Saving Time and its settings.

To toggle Home City time between standard time and daylight saving time

How to switch between standard time and DST for Home City.

Configuring Current Time and Date Settings

To change the current time setting

Procedure to adjust the current time setting (hour, minute).

To change the current date setting

Procedure to adjust the current date (day, month, year).

Using the Stopwatch (Stopwatch Split Mode)

What is a split time?

Definition and example of a split time measurement.

To perform elapsed time measurement

Instructions for starting and stopping elapsed time.

To pause at a split time

How to pause the stopwatch to record a split time.

Using the Stopwatch (Stopwatch lap mode)

What is a lap time?

Definition and example of a lap time measurement.

To perform an elapsed time operation

How to start, stop, and reset elapsed time in lap mode.

To perform lap time measurement

Instructions for measuring lap times.

To recall lap data

How to access stored lap times and the fastest lap.

Using the Countdown Timer

To specify the countdown start time

Setting the duration for the countdown timer.

To perform a countdown timer operation

How to start, stop, and reset the countdown timer.

Using the Alarm

To change the alarm time setting

Procedure to adjust the alarm time (hour, minute).

To check the AM/PM setting of the alarm

How to check the AM/PM indicator for the alarm.

To turn the alarm on or off

How to activate or deactivate the daily alarm.

Checking the Current Time in a Different Time Zone

To view the time in another time zone

Procedure to select and view time in different world cities.

To check whether a time zone is AM or PM

How to check the AM/PM indicator for a selected time zone.

To specify standard time or daylight saving time (DST) for a city

How to set standard time or DST for a selected city.

Adjusting Home Positions

To adjust home positions

Procedure to align watch hands and day indicator to their correct positions.

Troubleshooting

Hand Movement and Position

Troubleshooting issues related to hand movement and alignment.

Crown Operations

Troubleshooting common issues with crown operations.

Specifications