STANDARD HEATER APPLICATIONS
INSTALLATION & OPERATION INSTRUCTIONS
BKI
Æ
1418
The Cata-Dyne™ heater can be used in all
industrial indoor locations where a source of
infrared radiant heat is required, providing
adequate ventilation is available.
CERTIFICATION
Model WX (Series X) & MKII Cata-Dyne™
Explosion-proof, flameless infrared catalytic gas
heaters are certied by the Canadian Standards
Association (CSA) for use in Class I, Divisions 1
and 2, Group D hazardous (classied) locations
and FM Approvals, for use in Class I, Division
1, Group D hazardous (classied) locations,
temperature code T2C at an ambient temperature
of 40ºC (104ºF). WXS models are suitable for
Class I, Division I, Group D, temperature code
T2B at an ambient temperature of 40°C (104°F).
Models WX & MKII are certied ATEX/CE for use
in gas environments, Category 2, Zone 1 & 2,
Group IIA.
The Model BX (Series G) Cata-Dyne™ heater
is certied by CSA and FM for use in general
industrial non-hazardous locations. Models listed
are certied for industrial use only, for either
natural gas or propane gas. CSA approved models
are equipped for high altitudes: 0 - 4,500 ft. (0-
1,370 m) above sea level.
INSTALLATION
To ensure maximum efciency of your Cata-
Dyne™ heater, it should be installed with the
heating surface positioned plus or minus 45° from
the vertical plane at a height of no more than
8 ft. (2.44 m). All heaters must be installed in
accordance with the latest revisions of the codes
described in table 4 and in accordance with any
local codes and regulations. Before installing the
heater, all information on the heater nameplate
must be carefully reviewed. The nameplate lists all
the fuel and electrical requirements for the heater.
E-mail: info@ccithermal.com www.ccithermal.com
M20724-009 Date of Issue: July 2010
alteration, excessive vibration, service or maintenance
can cause property damage, injury or death. Read the
installation, operating and maintenance instructions
thoroughly before installation or servicing this equipment.
WARNING: Improper installation, adjustment,
Head Ofce & Factory:
5918 Roper Road, Edmonton, Alberta, Canada T6B 3E1
Telephone: (780) 466-3178 Fax: (780) 468-5904
Toll Free: 1-800-661-8529
Table 1
The WX Series Cata-Dyne™ features an improved efciency catalyst pad that required nearly 33%
less fuel to generate the same value as our BX Series Cata-Dyne™ heater.
10.543
50,000 60,000
BX 12 x 72 30,000 36,000 8.786
25,000 30,000 7.322 8.786
48,000 11.715 14.058
14.644 17.572
1.464 1.757
8.786 10.543
5.857 7.029
7.322 7.32225,000 25,000
4.393 5.272 30,000 36,000
10,000 12,000 2.929 3.514
20,000 24,000
13.179
4,167 5,000 1.220 1.464 45,000 54,000 13.179
2,222 2,667 0.651 0.781
15.815
36,000 8.786 10.543
45,000
5.4910.879 18,750 22,500BX 18 x 30
10.983
15,000 3.661 4.393 30,000
37,500
6.590
5,000 6,000 1.464 1.757 22,500 27,000 6.590 7.908
0.732
18,000 4.393 5.272
NAT
WX 12 x 36
WX 12 x 48
Approved for use in Class I, Division 1 and 2, Group D hazardous (classified) locations by both FM and CSA T-Code T2C @ 40°C Ambient
NAT
Max. Btu/hr
Model Number
LPG NAT LPG NAT LPG
BX 6 x 6
LPG
1,250 1,500 0.366 0.439 15,000
Cata-Dyne™ Heater - Models Available - CSA Only
WX 24 x 30
Specifications (Btu/hr Input Ratings)
For Both Natural and Propane Gas
WX 6 x 6
WX 12 x 24
5,000
MKII 12x12
MKII 12x24
MKII 18x24
MKII 18x48
Approved for use in general industrial non-hazardous locations by both FM and CSA
MKII 24x24
Specifications (Btu/hr Input Ratings)
For Both Natural and Propane Gas
Max. kW
BX 6 x 12
BX 6 x 24
2,500 3,000
BX 12 x 48
BX 12 x 60
WXS 6 x 12
Approved for use in Class I, Division 1, Group D hazardous (classified) locations by FM, T-code T2B at 40°C ambient
WXS 6 x 6
20,000 24,000 5.857 7.029 40,000
WXS 12 x 12
0.513
1.025
2.050
0.911
1.708WXS 10 x 12
WX 6 x 12
WX 6 x 24
WX 18 x 24
WX 18 x 30
WX 18 x 36
For Both Natural and Propane Gas
Max. Btu/hr Max. kW
WX 6 x 60
WX 8 x 8
WX 10 x 12
WX 12 x 12
BX Model (Series G)
MKII 24x48
Model Number
6,000
15,000 18,000
BX 6 x 60
BX 8 x 8
BX 10 x 12
BX 12 x 12
12,500
BX 12 x 24
BX 12 x 36
BX 18 x 24
WX Model (Series X)
Specifications (Btu/hr Input Ratings)
For Both Natural and Propane Gas
Approved for use in Class I, Division 1 and 2, Group D hazardous (classified) locations by both FM and CSA T-Code T2C @ 40°C Ambient
Model Number Model Number
WX 12 x 72
WX 12 x 60
Specifications (Btu/hr Input Ratings)
Model Number
Specifications (Btu/hr Input Ratings)
For Both Natural and Propane Gas
Max. Btu/hr Max. kW
BX 24 x 36
BX 24 x 48
BX 24 x 60
BX 18 x 36
BX 18 x 48
BX 18 x 60
BX 18 x 72
BX 24 x 24
BX 24 x 30
WX 24 x 24
WX 24 x 36
WX 24 x 48
WX 24 x 60
11.715
14.644
4.393
1.220
1.464
2.929
4.393
WX 18 x 48
WX 18 x 60
WX 18 x 72
20,000
40,000
Model Number
For Both Natural and Propane Gas
Specifications (Btu/hr Input Ratings)
WXS 12 x 24
1,750
3,500
7,000
3,111
5,833
7,000
14,000
WXS 6 x 24
WXS 8 x 8
2.050
4.100
Max. kW
Max. Btu/hr Max. kW
8.786
5.857
11.715
7.322
8.786
20,000
25,000
30,000
1,250
2,500
5,000
12,500
2,222
4,167
Max. kW
5,000
10,000
15,000
Max. Btu/hr
0.732
1.464
3.661
0.651
5.857
7.322
8.786
15,000
18,750
22,500
30,000
37,500
45,000
0.366
30,000
40,000
50,000
60,000
13.179
5.85720,000
25,000
5.491
6.590
8.786
10.983
30,000
1.464
2.929
4.393
17.572
5,000
10,000
15,000
Max. Btu/hr
WX 24 x 72
MK II Model (Series X)
To Next Page
Need help?
General