ccei LIMPIDO Z - User Manual

LIMPIDO Z : QUICK START
QUICK START OF THE DEVICE :
HIGH OR LOW SALT LEVEL WARNINGS & BACKWASH
ENTER ELECTROLYSE MENU
For a quick and efficient start of the electrolysis system, use the mode Production=ON. This mode will allow to
control the device together with the filtration system.
ENTER pH MENU
Set regulation on pH Dosage ph = pH- to bring pH down.
Set regulation on pH Dosage ph = pH+ to bring pH up.
The pH=ON mode is a continuous functioning mode which must be used only for pump priming.
NEVER LEAVE THIS SETTING ON, otherwise the pH bottle would empty quickly.
The device is provided with a safety on pH injection, which allows to set a maximum daily volume not to be
exceeded. For example, in a 40m3 pool, a daily dose of 0.3 litre/24h is enough. This setting can be done in the
pH menu: V/24h=0.3L.
SHORT FILTRATION POWER CUTS :
Warning : short power cuts (less than 1 minute) on the filtration pump or on 230V may lead to default of
the device. This default stops chlorine production but is not harmful to the device
When you face « lack of salt » of « high salt level », cut off the device for 5 minutes, then restart
the device after checking the electrolysis setting is not OFF. This operation can be enough to remove
the warning. If the default remains, check the real salt level into the pool as described in page 6 of the
user’s guide.
IN CASE OF BACKWASH :
Turn off the device while backwashing the filter. The device should remain turned off during backwash
(5 minutes)
For a correct setup of the probes, use
ZELIA-POD and connect the ground socket
of the ZELIA-POD on a ground rod which
is independent from the safety ground
equipment of the house. This independent
ground system must be as good as pos-
sible in order to increase the efficiency of
the probes (reading and lifetime).
USING INSTRUCTIONS
Injection pH
pH injection
Sonde pH
pH probe
Sonde ORP
ORP probe
PoolTerre intégré
Earthing device
Z3
Only
For a more precise electrolysis, use the mode Production=REG which will allow to control chlorine
production according to pool RedOx. See the instructions leaflet, on page 12 to buffer the RedOx probe and
to set the RedOx set value

Summary

Quick Start of the Device

Electrolyse Menu Configuration

Configure electrolysis mode (Production=ON/REG) and RedOx settings for efficient chlorine production and pool control.

pH Menu Configuration

Set pH regulation (pH-/pH+) and pH=ON mode for pump priming. Monitor daily pH injection volume.

Salt Level Warnings and Backwash Procedures

Impact of Power Cuts

Short power cuts may cause a default, stopping chlorine production but not harming the device.

Handling Salt Level Warnings

Restart device after 5 min for salt warnings. Check salt level if warning persists.

Backwash Procedure

Turn off the device during backwashing the filter for 5 minutes.

Using Instructions and Probe Setup

Probe Installation and Grounding

Correct probe setup requires ZELIA-POD and an independent ground rod for optimal efficiency and lifetime.

Flow Switch Control

Flow Detector Initial Check

Verify flow detector integration and function at first start-up.

Flow Light Indicator

Ensure the flow light appears on screen when the filtration system is active.

Chlorine Production Light

Confirm the production light activates when chlorine production is turned on.

Checking Flow and Production on Stop

Verify flow and production lights disappear when filtration stops; check for blockages.

Restarting Filtration and Lights

Restart filtration after a pause and re-check flow and production lights for proper function.

Overview

1. Function Description
2. Usage Features
3. Important Technical Specifications
4. Maintenance Features

The LIMPIDO Z is a device designed for pool water treatment, primarily focusing on salt chlorination and pH regulation. It offers both basic and advanced control options for maintaining optimal pool chemistry.

Function Description:

The core function of the LIMPIDO Z is to generate chlorine through electrolysis and regulate the pH level of the pool water. It achieves this by controlling the production of chlorine and the injection of pH-adjusting chemicals.

For chlorine production, the device offers two main modes:

• Production=ON: This is a basic mode for quick and efficient startup, allowing the device to operate in conjunction with the filtration system.
• Production=REG: This advanced mode enables more precise electrolysis by controlling chlorine production based on the pool's RedOx (oxidation-reduction potential) levels. Users can buffer the RedOx probe and set a desired RedOx value for automated control.

For pH regulation, the device can be configured to:

• pH Dosage ph = pH-: To decrease the pH level.
• pH Dosage ph = pH+: To increase the pH level.

An important safety feature for pH injection is the ability to set a maximum daily volume of pH-adjusting chemicals to prevent over-dosing. For example, for a 40m³ pool, a daily dose of 0.3 liters/24h is suggested, configurable via the pH menu (e.g., 24h=0.3L).

The device also incorporates a flow switch control mechanism to ensure proper operation. It checks for the presence of water flow through the cell before initiating chlorine production.

Usage Features:

The LIMPIDO Z features an intuitive interface with various menus and shortcuts for easy operation:

• Menu Navigation: Users can enter menus or sub-menus, validate choices, and browse through settings.
• Shortcuts: Dedicated shortcuts are available for SALT CHLORINATION and pH mode.
• Information Settings: Allows viewing of device information.
• Cancel/Go Back: A function to cancel a choice or return to a previous screen.
• Supervisor Mode Access: This advanced mode is accessed by cutting off the device supply, pressing and holding a button, then restarting and releasing the button. This mode likely provides access to more in-depth configurations and diagnostics.

Important Technical Specifications:

• pH Regulation: The device supports both pH- (acid) and pH+ (base) dosing.
• Chlorine Production: Controlled via electrolysis, with options for continuous (ON) or RedOx-regulated (REG) modes.
• Safety Features: Includes a maximum daily volume setting for pH injection and warnings for short filtration power cuts.
• Electrical Protection: The unit must be protected with a 30mA differential residual current protection. This is a critical safety requirement.
• Probes: The system utilizes a pH probe (Sonde pH) and an ORP probe (Sonde ORP) for monitoring and control.
• Earthing Device: An integrated earthing device (PoolTerre intégré) is part of the system. For optimal probe setup, it is recommended to use a ZELIA-POD and connect its ground socket to an independent ground rod, separate from the house's safety ground equipment. This improves probe efficiency and lifespan.

Maintenance Features:

The manual outlines several maintenance-related instructions and warnings to ensure the device's longevity and proper functioning:

• Flow Switch Control: Regular checks of the flow detector are crucial. During startup, the flow light should appear on the screen when the filtration system is on. If it doesn't, or if the production light doesn't disappear when filtration stops, the flow switch might be blocked.
• Salt Level Warnings: The device provides warnings for "lack of salt" or "high salt level." If these warnings appear, users should first cut off the device for 5 minutes, then restart it after checking that the electrolysis setting is not OFF. If the warning persists, the actual salt level in the pool should be checked as described in the user's guide.
• Backwash Procedure: During filter backwashing, the device should be turned off for the duration of the backwash (approximately 5 minutes).
• Short Filtration Power Cuts: The device warns that short power cuts (less than 1 minute) to the filtration pump or 230V supply can lead to a device default, stopping chlorine production. While not harmful to the device, it interrupts its function.
• pH=ON Mode Caution: The pH=ON mode is for pump priming only and should never be left on continuously, as it will quickly empty the pH bottle.
• Installation: For the installation of the salt chlorination cell, users are directed to follow the instructions in the main user guide.
• Probe Setup: Proper setup of the pH and ORP probes, including an independent grounding system, is highlighted as essential for increasing the efficiency and lifetime of the probes.

ccei LIMPIDO Z Specifications

General

Brand	ccei
Model	LIMPIDO Z
Category	Water Filtration Systems
Language	English