POWER ESPRESSO 20POWER ESPRESSO 20
4342
ENGLISH ENGLISH
- To get larger bubbles, insert the steamer by about 2 cm into the milk.
- To generate a denser foam with smaller bubbles, insert steamer 1 cm into the milk and tilt
it, placing the steamer spout on the lower side of the jug.
- When nished, turn the steam knob to the o position and press the steam button again
to deactivate the function.
Warning: clean the steam outlet with a wet sponge immediately after use. Then, remove the
steamer and clean the inner duct. It is also recommended to emit steam again to clean possible
milk remaining inside the tube.
- Pour frothed milk into the espresso to prepare cappuccino.
Note: it is recommended to allow the appliance to cool down for at least 5 minutes before
brewing coee again. Otherwise, your espresso might have a light burnt odour.
Dispensing hot water
- Press the coee button and make sure the steam knob is o. The indicator light will stop
blinking once the coee machine reaches the desired temperature.
- Turn the steam knob counterclockwise (at least 135º). Then, press the middle button. Hot
water will ow out from the steam outlet.
Steam-heating other liquids
- The steamer (without the tube) can be used to heat beverages like hot chocolate, water,
or tea.
- Remove the detachable water tank, open the tank cover, and ll it up. The water level
should not exceed the “MAX” mark in the tank. Install the tank back in the device.
- Plug the coee machine to a power supply. Make sure the steam knob is in the o position.
- Press the steam button and the indicator light will start blinking. Wait until the light stops
blinking.
- Remove the steamer from the steam outlet.
- Insert the steam outlet in the drink you wish to heat up. Slowly turn the steam knob
counterclockwise to release steam.
- When the required temperature is reached, turn the steam knob to the o position.
- Press the steam button again to turn the device o.
4. CLEANING AND MAINTENANCE
- Turn o, unplug the appliance, and let it cool down before cleaning it.
- Clean the housing of the appliance with a wet cloth. Empty the water tank and drip tray and
clean them together with the removable grille. Dry them thoroughly.
Note: Do not clean the appliance with alcohol or solvents. Do not immerse the main body of
the appliance in water.
- Clean the portalter and the stainless-steel lter under running water.
Cleaning mineral deposits
Clean the mineral deposits every 2-3 months to ensure that the coee machine operates
properly, that the internal piping is clean, and that coee avour is good.
1. Fill the tank with water and descaler up to the “MAX” mark (use the measure recommended
by the product manufacturer).
2. Insert the stainless-steel lter into the lter holder without ground coee in it and attach
it to the main body as indicated in previous sections. Place a jug under the lter holder.
Make sure the steam knob is in the o position.
3. Press the preheating-function button and wait until the indicator light stops blinking.
4. Then, press the coee button and dispense about 500 ml (20 . oz.) of liquid. Press the
coee button again to stop and wait for 5 seconds.
5. Press the steam button and wait until the indicator light stops blinking. Turn the steam
knob counterclockwise to release steam for 2 minutes. Then, turn the steam knob to the
o position and press the steam button again to stop. Allow the coee machine to cool
down for 15 minutes.
- Restart the coee machine and repeat steps 4 and 5 at least 3 times.
- Press the preheating-function button and wait until the indicator light stops blinking.
Then, press the coee button and dispense liquid until the water tank is empty.
- Fill the tank with clean water up to the “MAX” mark and repeat steps 4 and 5 at least 3
times.
5. TROUBLESHOOTING
Error Possible cause Possible solution
No coee comes out /
Very little coee comes
out / Coee comes out
unpressurised.
Remains of mineral
deposits in the device.
Perform a complete descaling
(Section 5.).
Coee was pressed
excessively / Coee is too
nely ground.
Do not exert too much pressure when
pressing the coee into the lter. /
Use more coarsely ground coee.
Coee is watery. The coee was too lightly
pressed. / Coee is too
coarsely ground.
Apply more pressure when pressing
the coee into the lter. / Use more
nely ground coee.