Why does the drink create a large head in the glass from Celli Dispenser?
If the drink from your Celli Dispenser flows out clear but creates a large head in the glass, it could be due to: * The glass being too hot. Dip the glasses in cold water to lower their temperature, using a glass-fountain if available. * Incorrect dispensing technique. Use the correct dispensing technique for the specific product.
Why does the drink have too much head from the Celli Dispenser?
If the drink flowing from your Celli Dispenser tap is too foamy, consider these potential causes: * Dirty tubes, keg connection, or tap: Immediately wash these components with a suitable detergent and rinse thoroughly. * Low CO₂ pressure: Calibrate to the correct equilibrium pressure. * Drink over-saturated with CO₂ gas: Unfortunately, if the drink is over-saturated, the only solution is to replace the keg. Excessively high pressure can also contribute; calibrate to the correct equilibrium pressure, maintain a consistent temperature in the keg storage area, and raise the kegs off the floor onto a platform. * Storage room temperature issues: Install air conditioning or relocate the storage to a more suitable environment. * Extended keg connection: If the drink keg has been connec...
What to do if the drink does not flow out of the Celli TE 15 L PRE-MIX tap?
If the drink from your Celli Dispenser tap isn't flowing, there could be several reasons: * The product may be frozen in the coil. Check the water temperature in the tank with a thermometer. If it's below 0°C, there might be drink in it, so replace the water and check for leaks. * The keg connection might not be firmly in place. Ensure it's properly connected. * The connection lever might not be hooked up. Make sure the lever is correctly hooked. * The drink keg could be empty. Replace it with a full one. * The CO₂/N₂ cylinder might be empty. Replace it with a full one. * The CO₂/N₂ cylinder valve might be closed. Open the valve. * There might be no pressure on the keg. Restore the operating pressure. * The drink tube could be bent. Check its path. * The drink tube could...
Why is there a quick loss of head in Celli TE 15 L PRE-MIX?
If you're experiencing a quick loss of head with your Celli Dispenser, it could be due to: * Traces of grease or detergent on the glasses: Wash the glasses well with a suitable detergent (in a glass-washer with brushes, if possible), then rinse thoroughly under running water. Using a glass-fountain is recommended. * Old drink keg: Replace the keg.
How to stop the Celli Dispenser tap from dripping?
If the tap of your Celli Dispenser is dripping, it could be due to: * A worn or faulty semicircular sealing gasket: Replace it with a new one. * Blocked drainage holes on the tap head: Clean the drainage holes.
Why does the drink emerge with an uneven head from Celli TE 15 L PRE-MIX?
If the drink from your Celli Dispenser emerges with an uneven head, it could be due to: * Keg connection badly inserted: Insert the connection firmly on the keg. * Drink line in contact with a heat source: Check the path of the product line and change it if necessary, or insulate the tube. * Keg connection gasket worn or faulty: Check and replace with a new one. * Empty keg: Replace the keg.
Why does the drink have too little head from the Celli TE 15 L PRE-MIX Dispenser?
If the drink from your Celli Dispenser has too little head, consider the following: * Drink temperature too low: Store the kegs in places with a suitable temperature. * CO₂ gas leak from the keg before dispensing: There is no solution; replace the keg. * Keg connection badly inserted: Insert the connection firmly on the keg. * Empty CO₂ cylinder: Replace the cylinder. * CO₂ cylinder valve closed: Open the valve. * CO₂ pressure reducer calibrated at an excessively low value: Restore the CO₂ equilibrium pressure.
What to do if the stirrer starter motor is idle in Celli TE 15 L PRE-MIX Dispenser?
If the cooling unit is working but the stirrer starter motor is idle in your Celli Dispenser, it could be due to: * No power supplied to the stirrer starter motor. Check the electricity supply system. * Stirrer starter motor failure. Replace the stirrer starter motor.
Why is the stirrer starter motor noisy in Celli TE 15 L PRE-MIX?
If the stirrer starter motor in your Celli Dispenser is noisy, it could be due to: * Ball bearing failure: Replace the stirrer. * Worn brasses: Replace the stirrer.
Why does the drink flow slowly from the Celli TE 15 L PRE-MIX Dispenser tap?
If the drink from your Celli Dispenser flows slowly, here's what might be happening: * The drink tube could be bent. Check its path to ensure it's not obstructed. * The tap compensator might be blocked. Disconnect the keg, disassemble the tap, remove the compensator, wash everything, and then reassemble. * The tap compensator might be adjusted in a semi-closed position. Turn the tap bolt anticlockwise to open it. * The drink tube might be obstructed. Wash out the drink lines to clear any blockages. * The connection on the keg might not be well inserted. Ensure it's firmly connected. * The CO₂/N₂ pressure might be too low. Restore the correct pressure, noting that the cylinder may be empty.
General| Category | Dispenser |
|---|---|
| Brand | Celli |
| Dispensing System | Pre-Mix |
| Material | Stainless Steel |
| Number of Taps | 1 |
| Model | TE 15 L |
| Capacity | 15 L |
| Power Supply | 220-240V / 50-60Hz |
To Next Page