Page 8 0D7'>89:EG9;5'N48C>GDECO'A58;C8'9;55'PBQQQBQRRBSTUT Item 57209
2#0&,- (*&$#,.(V )#.V,&V#V!&2&,1*
(A87;>GE<'.EC>749>GDEC
1CGE<'>:8'WD7_'+G<:>
1. To turn the Work Light on, press the Power Button
ON and then press the Work Light button.
2. To turn the Work Light off, press
the Work Light button again.
3. If finished using the Jump Starter,
press the Power Button OFF.
`4@AB2>;7>GE<';'H8:G958
VD>8J Read the vehicle owner’s manual pertaining
to jump-starting prior to using the Jump Starter.
1. Press the Power Button ON and check the Battery
Status Indicator Lights to verify that the Jump
Starter is fully charged. Recharge as needed,
following the instructions in the f!:;7<GE<'
>:8'`4@A'2>;7>87g'section on page 7.
2. Turn off the vehicle ignition switch and all
accessories (lights, radio, climate control, etc.).
3. Turn Clamp Switch on the Jump Starter
to the OFF position. You may leave
the Work Light on if needed.
W#$V.V%['',('*$&H&V,'2&$.(12'.V`1$-J
/('V(,',(1!"'*(2.,.H&'#V/'V&%#,.H&'
X#,,&$-'!+#)*2',(%&,"&$3
3. Connect the red Positive Battery Cable to
vehicle’s positive battery terminal. Connect
the black Negative Battery Cable to a non-
moving metal part of the vehicle.
W#$V.V%[ ',('*$&H&V,'2&$.(12'.V`1$-J''
/('V(,'!(VV&!,',(',"&'V&%#,.H&'
,&$).V#+'(0',"&'X#,,&$-3
W#$V.V%['',('*$&H&V,'2&$.(12'.V`1$-J''/('
V(,',1$V'!+#)*'2W.,!"',('(V'*(2.,.(V'
.0',"&'$&H&$2&'*(+#$.,-'W#$V.V%'+&/'
.2'(V'#V/',"&'#+#$)'X1hh&$'.2'"&#$/3''
2,(*'#V/'!($$&!,',"&'*$(X+&)3
4. When the correct connection has been made,
turn the Clamp Switch to the ON position.
5. W#.,'0.H&').V1,&2O then start the
vehicle. If the vehicle does not start, wait an
additional 3 minutes before trying again.
V(,.!&J'',"&'H&".!+&'W.++'V(,'2,#$,'.0'
-(1'/('V(,'W#.,'#,'+,'S').V1,&23
6. After the vehicle is started, turn the
Clamp Switch to the OFF position. Remove
the black Negative Battery Cable first, and
then the red Positive Battery Cable.
$4EEGE<K!:;7<GE<'12X'/8ZG98C
1. Press the Power Button ON and check the Battery
Status Indicator Lights to verify that the Jump
Starter is fully charged. Recharge as needed,
following the instructions in the “!:;7<GE<'>:8'
`4@A'2>;7>87” section on page page 7.
2. Plug the device into the USB Port.
3. When finished, unplug the device from the USB Port.
4. If finished using the Jump Starter,
press the Power Button OFF.
To Next Page
Loading...
Need help?
General