Chamberlain 940CD-01 - User Manual

Model 940CD-01 Security✚
®
Wireless Keyless Entry
™
/
FEATURES
For use with any 315 MHz Security✚
®
garage door opener
having a purple “learn” button.
Personalized Password: Up to 10,000 possible combinations.
Password can be easily changed if desired.
Temporary password: Can be added for visitors or service
persons. This temporary password can be limited to a
programmable number of hours or a programmable number of
entries.
Rolling Code: While your password remains constant until you
change it, the code between the Keyless Entry and the receiver
changes with each use, randomly accessing over 100 billion
new codes.
Operation: Opener activates when 4-digit password and
ENTER button is pressed.
If wrong numbers are accidentally pressed, correction can be
made immediately. The ENTER button will transmit only the last
four digits.
The keypad will blink for 15 seconds after the password is
transmitted. During that time the ENTER button can be used to
stop or reverse the door travel.
The Lock feature on openers with Multi-Function Door Controls
is designed to prevent operation of the door from portable
transmitters. However, the door will open and close from the
door control push button and the Keyless Entry.
One Button Close: Opener can be closed by pressing only the
ENTER button if the one button close feature has been
activated. This feature has been activated at the factory. To
activate or deactivate this feature press and hold buttons 1 and
9 for 10 seconds. The keypad will blink twice when the one
button close is active. The keypad will blink four times when one
button close is deactivated.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
1. Enter a four digit personal identification
number (PIN) of your choice on the keypad.
Then press and hold enter.
2. While holding the ENTER button, press and
hold the LIGHT button on the Multi-Function
Door Control.
3. Continue holding the ENTER and LIGHT
buttons while you press the push bar on the
Multi-Function Door Control (all three
buttons are held).
4. Release buttons when the motor unit lights
blink. It has learned the code. If light bulbs
are not installed, two clicks will be heard.
1. Press and release the “learn” button on motor
unit. The learn indicator light will glow
steadily for 30 seconds.
2. Within 30 seconds, enter a four digit personal
identification number (PIN) of your choice on
the keypad. Then press and hold the
ENTER button.
3. Release the button when the motor unit lights
blink. It has learned the code. If light bulbs
are not installed, two clicks will be heard.
L
O
C
K
L
I
G
H
T
SETTING THE PERSONAL ENTRY PASSWORD
We recommend that you program your password now,
before you install the Keyless Entry. Then you can test the
reception at the mounting location before you proceed
further.
USING THE “LEARN” BUTTON
USING THE MULTI-FUNCTION DOOR CONTROL
Side two contains instructions for installing the Keyless
Entry, changing the personal entry password and setting a
temporary password.
L
O
C
K
L
I
G
H
T
L
O
C
K
L
I
G
H
T
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• Install Keyless Entry Control within sight of the garage door, out of
reach of children at a minimum height of 5 feet (1.5 m), and away
from all moving parts of door.
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION
WARNING
WARNING
1

Summary

Features of the Keyless Entry

Personalized Password

Allows setting a unique personal password for garage door opener access.

Temporary Password Functionality

Enables setting time-limited or entry-limited passwords for visitors or service.

Rolling Code Security

Explains how the code changes with each use for enhanced security.

Keypad Operation and Control

Details how the opener responds to 4-digit password entry and ENTER button.

One Button Close Feature

Describes activating/deactivating the feature to close door with single ENTER press.

Safety Warnings and Notices

General Safety Precautions

Crucial safety advice to prevent injury from moving doors and keep remotes away from children.

FCC Compliance Notice

States compliance with FCC rules and prohibits unauthorized adjustments.

Setting Up Your Keyless Entry

Using the Learn Button

Step-by-step guide to programming the Keyless Entry using the motor unit's learn button.

Using the Multi-Function Door Control

Instructions for programming the Keyless Entry via the multi-function door control.

Installation and Mounting

Location Selection Criteria

Guidance on choosing an appropriate, safe installation location for the Keyless Entry.

Mounting Instructions

Detailed steps for physically attaching the Keyless Entry unit to the wall or door jamb.

Password Management

Change Existing PIN

Procedure for updating the primary 4-digit personal entry password.

Set Temporary PIN

Steps to program a temporary PIN for visitors or service personnel.

Temporary PIN Usage Options

Explains how to define the duration or number of uses for a temporary PIN.

Keyless Entry Battery

Battery Maintenance and Replacement

Information on battery life, replacement indicators, and proper disposal.

Chamberlain 940CD-01 Specifications

General

Brand	Chamberlain
Model	940CD-01
Category	Remote Starter
Language	English