Charles WIC-101010SXAN1 - User Manual

LT-WIC101010
3
rd
Printing, July 15, 2020
©Copyright 2020 Charles Industries LLC. All Rights reserved. Printed in the United States of America.
Availability of features and technical specifications herein are subject to change without notice.
Charles is a registered trademark of Charles Industries.
Page 1 of 16
Charles Universal Broadband Enclosure
WIC-101010SXAN1
General Description and Installation
1. GENERAL INTRODUCTION ...................................................... 1
1.1. Document Purpose ................................................................... 1
1.2. Product Purpose ....................................................................... 1
1.3. Product Mounting and Location ............................................... 1
2. PRODUCT DESCRIPTION ........................................................... 2
3. INSTALLATION ............................................................................ 6
3.1. Inspecting the Product .............................................................. 6
3.2. Following and Using Safety Precautions.................................. 6
3.3. Obtaining Tools and Equipment ............................................... 6
3.4. Preparing the Installation Site .................................................. 6
3.5. Lifting the WIC ......................................................................... 7
3.6. Mounting the WIC .................................................................... 7
3.7. WIC Wiring and Equipment.................................................... 10
3.8. Conduit Seals.......................................................................... 13
3.9. Verifying the Installation ........................................................ 13
4. PERIODIC MAINTENANCE ...................................................... 13
5. TECHNICAL ASSISTANCE AND REPAIR SERVICE ........... 13
6. WARRANTY & CUSTOMER SERVICE ................................... 13
7. SPECIFICATIONS ....................................................................... 13
7.1. Regulatory Specifications ....................................................... 13
7.2. Product Specifications ............................................................ 14
7.3. Part Numbers ......................................................................... 14
7.4. Alarm Connections ................................................................. 15
1. GENERAL INTRODUCTION
1.1. Document Purpose
This document provides general information for the WIC-101010SXAN1 walk-in cabinet. Figure 1 shows a closed front view of the
enclosure.
-NOTE-
Hereafter, the Charles Walk-in Cabinet WIC-101010SXAN1 will be referred to as the “WIC.”
1.2. Product Purpose
The WIC consists of a protective walk-in enclosure for an integrated system of electronic components and equipment that can serve fiber
and copper interfaces. Note: this enclosure is not intended for use as a dwelling and is not suitable for human or animal habitation.
1.3. Product Mounting and Location
This enclosure is suitable for outside plant-type (OSP) locations and those that may require NEC compliance. The outdoor, weather-
resistant WIC is to be mounted on a concrete pad. The installer connects the power, fiber and copper connections. Detailed mounting and
installation information is covered in Section 3.
Figure 1 Front View of the WIC

Summary

General Introduction

Document Purpose

Provides general information for the WIC-101010SXAN1 walk-in cabinet.

Product Purpose

Describes the WIC as a protective walk-in enclosure for integrated electronic systems.

Product Mounting and Location

Details suitability for outdoor locations and NEC compliance, requiring mounting on a concrete pad.

Product Description

Installation

Inspecting the Product

Visually inspect the unit for damages prior to installation and report any transit damage.

Safety Precautions

Follow NEC, local codes, and safety procedures; ensure proper grounding and use trained personnel.

Obtaining Tools and Equipment

Lists recommended tools and equipment for installing the WIC, including safety gear.

Preparing the Installation Site

Recommendations for site preparation, including spacing, safety, and pad requirements.

Lifting the WIC

Procedure for lifting the WIC using forklift or crane, including required equipment.

Mounting the WIC

Details mounting on concrete pads or using EMI mounting kits, ensuring the unit is level.

Mounting with EMI Helical Mounting Kit

Step-by-step instructions for installing the WIC using the EMI Helical Mounting Kit.

Mounting with EMI Gravity Mounting Kit

Instructions for using the EMI Gravity Mounting Kit, including site grade considerations.

Mounting with EMI Extension Mounting Kit

Procedure for using the EMI Extension Mounting Kit with concrete pad extensions.

WIC Wiring and Equipment

Torque Requirements

Specifies torque values for hardware used in mounting and connections.

Ground Connection

Details external and internal ground bar connections and earth ground requirements.

CTMS Operation

Explains the operation of the CTMS thermal devices, including fan speed control.

IVS Operation

Describes the Intelligent Ventilation System (IVS) operation via timer or internal temperature probe.

HVAC Operation

Details the HVAC kit operation, including cooling and heating cycles.

Fiber and Copper Entry

Locations and types of cable entry ports for fiber, copper, and conduit.

Periodic Maintenance

Enclosure Opening Precautions

Guidance for opening the enclosure in freezing conditions and using de-icer spray.

GFCI Receptacle Reset

Instructions for resetting the GFCI receptacle and indicators for faults.

Technical Assistance and Repair Service

Specifications

Regulatory Specifications

Lists regulatory standards the WIC is designed to meet, including UL and GR-487.

Product Specifications

Provides physical, electrical, thermal, environmental, and kit specifications.

Part Numbers

Lists Charles part numbers and descriptions for different WIC configurations.

Alarm Connections

Details alarm block configurations, BBU wire colors, and AT&T alarm labels.

Charles WIC-101010SXAN1 Specifications