Chicco CuociPappa Natural - Troubleshooting Guide; Technical Data

36
XI. TECHNICAL DATA
Model: MEC-6131V
Supply voltage: 220-240 V~, 50/60 Hz
Boiler power: 400 W
Motor power: 140 W
Blender operating cycles: 10 sec. ON – 10 sec. OFF
Made in China
This product complies with the Directive 2012/19/EU.
The crossed bin symbol on the appliance indicates that the
product, at the end of its life, must be disposed of separately from
domestic waste, either by taking it to a separate waste disposal
site for electric and electronic appliances or by returning it to
your dealer when you buy another similar appliance. The user is
responsible for taking the appliance to a special waste disposal
site at the end of its life. If the disused appliance is collected
correctly as separate waste, it can be recycled, treated and dis-
posed ecologically; this avoids a negative impact on either the
environment and health, and contributes towards the recycling
of the product’s materials. For further information regarding
the waste disposal services available, contact your local waste
disposal agency or the shop where appliance has been bought.
Warranty
This appliance is guaranteed against manufacturing defects for
two years from the date of purchase (the date shown on the re-
ceipt or other proof of date of purchase) or for any other period
envisaged by the applicable law in the country of purchase. The
warranty does not cover parts subject to normal wear.
CE DECLARATION OF CONFORMITY
Artsana S.p.A herebydeclares that this Chicco appliance, MOD.
MEC-6131V,complieswithalltheessentialrequirementsandother
provisions indicated in the EU Directives 2004/108/EC (electro-
magnetic compatibility) and 2006/95/EC (electrical safety) and
2011/65/EU(RoHS).AfullcopyoftheECdeclarationcanbere-AfullcopyoftheECdeclarationcanbere-Afullcopyofthe ECdeclarationcanbere-
questedfromArtsanaS.p.A.ViaS.Catelli1,22070Grandate(Co)
Italy.
X. TROUBLESHOOTING
PROBLEM POSSIBLE CAUSES POSSIBLE SOLUTIONS
The display does not
come on
· Power cord not properly inserted in the ap-
pliance
· Check that the power cord is inserted correctly into the
connector and that the appliance is plugged in
The symbol appears on the
display and there is a beep
every 10 seconds
· The water tank is missing or has not been
filled or positioned correctly
· The water does not flow freely from the tank
to the boiler
· Lime scale accumulation in the boiler
· Switch off the appliance and unplug it. Fill the tank with
water before restarting the cycle.
· Switch off the appliance and unplug it. Leave it to cool
completely (at least 30 minutes) then clean.
· As above
The symbol appears on the
display
.
· The boiler has overheated due to the accu-
mulation of lime scale
· The boiler has overheated due to repeated
cooking cycles
· Switch off the appliance and unplug it. Leave it to cool
completely (at least 30 minutes) then clean.
· Leave the appliance to cool between one cycle and the
next
The appliance will not
blend or the cooking cycle
will not start
· The jug or the lid are not in the right position · Position the jug and lid correctly so that the safety
switches are activated
A bad smell or excessive
noise comes from the mo-
tor unit during blending
· New product
· Too much food
· Food that is too hard in the jug
· Blending times too long
· During the first uses, this is normal
· Reduce the amount of food in the jug
· Do not blend food that is too hard. Defrost food before
blending it.
· Follow the recommended blending times, leaving the
appliance to cool to prevent overheating.
Food leaks from the jug
during blending
· Too much food in the jug or the food is too
liquid
· Reduce the amount of food or liquid in the jug
The appliances takes too
long to produce steam or
does not produce any
· Limescale accumulation in the boiler · Perform cleaning and maintenance on the boiler
The food is not cooked
properly
· Pieces of food too large
· Too much food in the basket
· Cooking times not adequate
· Cut food into smaller pieces
· Reduce the amount of food
· Set longer cooking times
Steam coming out of the
boiler cap area
· The boiler cap is not inserted or is not prop-
erly closed
· The steam outlet is obstructed by food resi-
due or limescale
· Position the boiler cap and close it well
· Perform cleaning and maintenance on the boiler. If neces-
sary, clear the steam outlet without damaging the seal
The “add water” signal is
activated at the start of or
during the cooking cycle
· The water tank is missing or has not been
filled or positioned correctly
· The water does not flow freely from the tank
to the boiler
· Position the tank correctly after filling it with a suitable
volume of water
· Perform cleaning and maintenance on the boiler
The cap will not come off
the jar after cooking
· Overheating · Wait a few minutes and allow to cool
After cooking, there is wa-
ter under the water tank or
under the appliance
· Blade unit missing or positioned incorrectly
· Blade seal missing or positioned incorrectly
· Insert the blade unit in the jug and turn it until it is se-
curely fitted
· Check the presence and position of the seal
Water leaking from the
tank
· Cap not closed properly
· Seals missing or positioned incorrectly
· Tighten the cap
· Check the presence and position of both seals