05 Connection priority
06 Connecting via Bluetooth
Bluetooth is a lossy means of transmitting audio
data. For best results, use Wi-Fi wherever possible.
Make sure that Poly is connected to a
switched-on Mojo
1
In your device’s Bluetooth settings search for
devices
2
Locate Poly and when prompted, input the
code: 0000
3
Poly prioritises Bluetooth connections over Wi-Fi for ‘on-
the-go’ convenience. If a Wi-Fi connection is established
you may interrupt this connection by selecting Poly as
the output from your device. Poly will only be able to re-
engage Wi-Fi connectivity once the Bluetooth connection
is disconnected.
IMPORTANT
Poly has a maximum Bluetooth range of fi ve
metres, distortion may occur beyond this.
INPUT
PRIORITY
ALWAYS
PRIORITISED
WHEN BLUETOOTH
DISCONNECTED
1 2
If you wish to switch between Roon and other you
must manually engage this before each session.
Open a web browser window, Poly’s internal
webpage will now be displayed for confi guration
4
Enter the SSID of your network followed by
the network password
5
With your device connected on the same
network as Poly, you can now use your
chosen apps for playback including; AirPlay
(iOS), DLNA, and Roon
8
When a new network is added, Poly will
reboot. Allow ten seconds for this sequence
to complete. When Poly switches back on, it
will search for your network, indicated by the
P-status LED fl ashing blue. Once connected
will display a solid colour - battery status will
now be indicated
7
Select ‘playback mode’. If you are using
Roon then you must select ‘Roon mode’, for
everything else select ‘Other’. Then click ‘Save’
6
We recommend attaching the included pin to your
keyring for safekeeping.
For devices that are unable to create a personal
hotspot, the GoFigure app will allow Poly to create
its own local hotspot that you can connect to. For
more information see section 08 of this manual.
A free app to confi gure your Poly is available for iOS and
Android devices. GoFigure allows you to confi gure your
networks, change playback modes, and more
06 Configure using the GoFigure App
Confi guring your Poly using the GoFigure app is
recommended, rather than confi guring via WiFi which is
covered in section 07 of this manual.
To download GoFigure search the Google
Play and/or App Store for ‘Chord Electronics’
or ‘GoFigure’
1
GoFigure communicates with Poly via
Bluetooth. Whilst downloading, enter your
device’s settings menu and turn on Bluetooth
2
Turn on Mojo, connect Poly and wait for Poly
to initialise
3
Open GoFigure
4
07 Configure via Wi-Fi
Wi-Fi is typically lossless & offers the best means
of transmitting audio data. Use whenever possible.
Open the Wi-Fi settings on
any device and select Poly to
connect to the unsecured Wi-Fi
network
3
Poly must be placed in Access Point mode.
To add a new network use the included pin
to press the ‘Confi g’ button for fi ve seconds
When Access Point mode is established,
Poly’s P-status LED will fl ash green and
then blue, repeating the sequence. Poly’s IP
address will also be played through Mojo
2
Make sure that Poly is connected to a
switched on Mojo, if active, the P-status
LED will illuminate
1
(without the GoFigure app)
08 Confi guration/Wi-Fi help
Poly communicates only via 2.4GHz networks and
has a maximum range of 10m.
The SSID of your network is the name
that your network broadcasts. You can
usually fi nd this and your password by
looking at the bottom of your router.
Locating router SSID and password
If connecting Poly to a mobile device you will need to
activate your personal hotspot. During transmission, Poly
will not consume any data.
To view your SSID go to the Settings menu >
General > About > Name - this is your SSID.
To connect Poly to your iOS device, engage your
personal hotspot and view password via: Settings
> Personal Hotspot.
Locating Apple iOS SSID and password
To view your SSID, password and engage personal
hotspot, go to the Settings menu > Wireless &
Networks > More > Tethering & Portable Hotspot.
Locating Android SSID and password
Poly provides feedback via the P-status LED. Below you can
discover the connection and charge status.
02 Charging
All Mojo battery status indicators remain the same
via the M-status.
Poly is in access point mode - connect to
Poly’s unsecured Wi-Fi and enter your valid
Wi-Fi network details to allow Poly to connect
Poly is searching for a known Wi-Fi network
Poly has successfully connected to a known
network - battery status will now be shown*
Poly has successfully read the inserted
Micro SD card
Flashing
Flashing
Flashing
When Bluetooth input is operational, only charge
status will be indicated window clear of obstacles.
Charging 75% - 100% 50% - 75%
25% - 50% 5% - 25% 0% - 5%
*
Before using Poly for the fi rst time, we recommend
that you fully charge your device for six hours.
Below are average charging and playback times for Mojo
and Poly when connected together.
03 Understanding Poly’s status
To charge Poly on its own you must use a charger capable
of delivering at least 1amp of current.
You can simultaneously charge Poly and Mojo
whilst playing back audio. To do this you must use a
charger capable of delivering 2 Amps.
When charging, Poly’s P-status LED will show a
steady solid white glow.
Using a 1amp charger when Poly and Mojo are
connected will result in only Mojo being charged.
hours
hours
hours
hours
amps
PLAY
&
CHARGE
Playback
hr
9
Poly charge
time
Mojo charge
time
Charger
2 4
4
4
8
(average)
04 Switching on Poly
Wait ten seconds for Poly to
register connection. Poly’s P-status
LED will now become active
3
To protect the connection we
advise purchasing the Poly case.
If Poly does not wake upon connection, disconnect
from Mojo and connect to a charger for one hour.
Poly features an auto-on circuit that wakes the
device upon connection to a switched on Mojo.
Connect Poly to Mojo, making sure to not use
excessive force and consider using a fl at surface
1
Turn Mojo on and wait until
switch-on sequence completes
2
To Next Page
Need help?
General
