EasyManua.ls Logo

Cincinnati Fan PB User Manual

Default Icon
15 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
OMM-23-1009-page 1
Installation, Safety, Operation & Maintenance Instructions And Parts List
For Models PB, PBS, SPB and LM.
Arrangement 4D Double Blowers
All Cincinnati Fan products are packaged to minimize any damage during shipment. The freight carrier is responsible
for delivering all items in their original condition as received from Cincinnati Fan. The individual receiving this equipment
is responsible for inspecting this unit for any obvious or concealed damage. If any damage is found, it should be noted
on the bill of lading before the freight is accepted and the receiver must file a claim with the freight carrier.
ATTENTION: RECEIVING DEPARTMENT
READ ENTIRE MANUAL, INCLUDING “SECTION IV. INITIAL UNIT STARTUP” BEFORE
ATTEMPTING TO INSTALL AND OPERATE THIS EQUIPMENT.
NOTE
This blower has a unique design in that it has a blower housing and wheel assembly mounted to both ends of the motor. The instruc-
tions contained in this manual pertain to both blowers mounted on either side of the motor. The blower housings, wheels, inlets and
discharges can be the same or different as required by the application. Make sure you follow all instructions for both blower assem-
blies. If you need to order any replacement parts, special instructions may be required.
NOTICE
LONG TERM STORAGE NOTICE
If this blower will NOT be installed and put into operation within 30 days, refer to the “Long Term Storage
Instructions” on pages 12 and 13. Failure to follow all applicable long term storage instructions, will void your
warranty. This blower should be stored indoors in a clean, dry location.
BLOWER SERIAL NUMBER: ________________________ MFG. DATE: ____________________
NOTE: The serial number above is a required reference for any assistance. It is stamped on the blower nameplate.
BLOWER SPECIFICATIONS:
Model: ________ Arrangement: ________
BLOWER PERFORMANCE DATA: (If entered on order)
CFM: ________ SP: ________ (Inches of Water Gauge) Motor BHP: ________
Density: ________ Altitude: ________ (Ft. above S.L.) Airstream Temperature: ________°F.
Fan RPM: ________ Maximum Safe Fan RPM: ____________ DO NOT EXCEED THIS RPM
MOTOR DATA: (This section is completed only if the motor was supplied by Cincinnati Fan)
HP: __________ RPM: ____________ Voltage: ______________________________ Phase:________
Hz: ___________ Frame Size: ___________ Enclosure: ____________ Efficiency: ____________
IF Motor is EXP, Class(es) & Group(s) are:_________________________
Manufacturers Model Number: ___________________________ CFV Part Number: ___________
BLOWER SPECIFICATIONS
Form: OMM-23-1009
Effective: 10/30/09
Part No.: 01249

Other manuals for Cincinnati Fan PB

Questions and Answers:

Cincinnati Fan PB Specifications

General IconGeneral
BrandCincinnati Fan
ModelPB
CategoryBlower
LanguageEnglish

Summary

Blower Specifications and Data

Blower Performance Data

Details on CFM, Density, Fan RPM, Motor BHP, Altitude, and Temperature.

Motor Data

Information on motor HP, RPM, Voltage, Frame Size, Enclosure, Phase, and Efficiency.

General Safety and Handling

DANGER and WARNING Symbols

Highlights critical safety symbols and their meanings for immediate attention.

Unpacking and Handling Procedures

Guidance on safely removing and handling the blower from its packaging.

Safety Accessories and Instructions

Details on required safety accessories and referenced safety publications.

Installation and Component Details

Vibration Considerations

Awareness of vibration effects and proper installation to prevent bearing failure.

Mounting Methods

Instructions for floor and elevated mounting, including foundation requirements.

Duct Work Connections

Guidelines for connecting ductwork, including flexible connectors and clearance requirements.

Safety Guards and Dampers

Information on mandatory safety guards and airflow control devices like dampers.

Electrical Setup and Motor Operation

Disconnect Switches

Importance of independent disconnect switches and lockout/tagout procedures.

Motor Wiring and Connections

Guidelines for proper motor wiring, voltage, and phase connections.

Motor Maintenance and Protection

Guidance on motor cleaning, lubrication, and protection from environmental factors.

Initial Unit Startup Procedures

Pre-Startup and Post-Startup Checks

Detailed checklist for essential pre-startup and post-startup inspection tasks.

Initial Vibration Analysis

Procedures for measuring and recording initial vibration levels after installation.

Routine Inspection and Maintenance

Hardware Checks

Ensuring all blower and foundation hardware is tight, including set screws.

Motor Bearing Lubrication

Guidelines for lubricating motor bearings, including frequency and grease type.

Wheel Balancing and Vibration

Methods for balancing wheels and addressing vibration causes.

Troubleshooting Common Issues

Identifying and resolving common problems like excessive vibration or low airflow.

Long Term Storage and Warranty

Long Term Storage Instructions

Essential steps for storing the blower for over 30 days to maintain warranty.

Limited Warranty Details

Information on the warranty period, exclusions, and obligations.

Limitation of Liability and Returns

Understanding liability limits, claims process, and return procedures.

Parts Drawing and Information

Obtaining Parts Drawings

How to access specific parts drawings and contact sales for information.

Related product manuals