Cinecta MX-1 - User Manual

CINECTA MX-1 user’s manual
Dear User,
We would like to introduce you to the CINECTA MX-1 camera stabilizing system.
The CINECTA MX-1 camera stabilizing system was specifically developed for DSLR cameras. It can be
used for any camera as long as it weighs less than 2 kilograms. Our system helps you shoot wobble
and judder-free video even when moving quickly over an uneven surface.
The CINECTA MX-1 camera stabilizing system consists of three main parts:
 CINECTA MX-1 supportive vest
 CINECTA MX-1 stabilizing arm
 CINECTA MX-1 sled
In order to set up your new camera stabilizing system it’s indispensable that besides reading this
written manual you follow our video on the subject. The video can be found here:
www.cinecta.com/video, or directly available on our website under the Videos Menu.
To follow the steps of the manual please also watch our video!
The CINECTA MX-1 stabilizer vest attaches the system to the cameraman's body; it evenly distributes
the weight of the rig and the camera on the user's upper body. If accurately set it makes fieldwork
easy and effortless.
The vest can be adjusted to the height of the user with the thumbscrew located on the front. The
heavy-duty buckles and straps securely hold the rig - for this, it is absolutely necessary that the straps
are set as tight as possible without causing discomfort. With loose straps the device cannot operate
properly, such use may be dangerous, and could damage the system. The proper adjustment of the
waist is also very important; adjust its height to fit to the height of your hipbone.
The purpose of the CINECTA MX-1 sled is to stabilize the camera vertically, and this part makes it
possible that the cameraman could move the camera freely to the required direction. Special bearing
ensures precise operation. The sled can be used without the other elements of the system, by
holding in hand, but in this way it cannot reach the same stability that the complete system provides.
The precise adjustment of the sled is paramount for perfect wobble free shots.
The sled is not shipped fully assembled, as a first step with the included screws and Allen wrench
attach the stage assembly –later you will attach your camera on the top of this.
The lower weight bracket can be installed in two ways for practical reasons – the angle of its setup
depends on the weight distribution of your camera and also on the angle that the camera sets with
the stage unit.
The sled has a gimbal assembly, which allows smooth movements in all directions and balance at the
same time.

Summary

Introduction and System Components

CINECTA MX-1 Stabilizer Vest

Attaches the system to the cameraman's body, distributing weight evenly. Adjustable for user height and waist.

CINECTA MX-1 Sled

Stabilizes the camera vertically, allowing free movement. Features special bearings for precise operation and a gimbal assembly.

CINECTA MX-1 Stabilizing Arm

Acts as a shock absorber, filtering vibrations from cameraman's movement. Features a ball bearing mechanism and adjustable spring tension.

System Setup and Balancing

Camera and Weight Balancing

Mount camera to ensure center of gravity aligns with center post. Adjust weights for cameras between 1-2 kg for horizontal balance.

Gimbal Fine Tuning

Adjust gimbal until center post slowly turns vertical, achieving a 2-3 second fall. Ensure no tilt during sled movement.

System Operation

Attaching Components

Attach stabilizing arm to vest, then gimbal assembly to the arm. Fine tune arm tension for camera weight.

Filming Technique

Guide rig with fingertips on center post and gimbal handle. Maintain a straight posture for proper operation and quality recording.

Practical Advice

Exercise caution, check components, wear appropriate clothing. Plan moves, be aware of surroundings, and avoid finger injuries.

Maintenance

Component Care

Bearings are maintenance-free. Lubricate adjustment screw if stiff. Keep connector parts clean with a dry cloth.

Environmental Precautions

Do not use the device in dusty or wet environments to prevent damage and ensure longevity.

Cinecta MX-1 Specifications

General

Brand	Cinecta
Model	MX-1
Category	Camera Accessories
Language	English