1/4
C650/C651/C652 Abbreviated instruction
• This watch is solar-powered. Expose the dial to light and use it sufficiently charged.
• To see details of charging time, specifications and operations, refer to the instruction manual:
C650/C651/C652 instruction manual
English
Component identification
Hour hand
24-hour hand
Area name display
Power reserve
indication
Second hand
Crown
UTC hour hand/ UTC minute
hand
60
70
80
90
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
30
35
40
45
50
55
10
KM.
70
80
90
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
30
35
40
45
50
55
10
N
A
U
T.
S
T
A
T.
Button
B
Mode hand
Minute hand
Digital display
Button
A
Crown's position
0 1 2
• Actual appearance may differ from the illustration.
• The crown has two positions when pulling it out.
• Refer also to our web page for detail of usage of the scale and bezel on the watch.
(
http://www.citizenwatch-global.com/support/pdf/enhanced/e.pdf
)
Checking the power reserve
The poser reserve indication indicates the current power reserve.
• Indication example: C650/C651.
Level 3 2 1 0
Power reserve level
scale
Meaning
Power reserve
is sufficient.
Power reserve is
OK.
Power reserve is
getting low.
Insufficient
charge warning
has started.
Charge immediately.
Time setting warning function (only for C650)
Hands and the digital display warn the user as below to set the time correctly
when the watch is charged again after it stopped because of insufficient charge.
• Hands except mode hand: move to reference positions
• Area name display / digital display: blink
Adjust the time and calendar.
Setting the time of the digital section
• To set the time of the analog section, refer to “Switching the time of analog and
digital sections”.
1.
Push the crown in to position
0
.
2.
Rotate the crown to move the mode hand to point [TME].
3.
Press and release the lower right button
A
or upper right
button
B
repeatedly to indicate an area name you want on the
area name display.
• For area names, refer to the table on “Using the world time”.
4.
Pull the crown out to position
2
.
The second hand points 0 second and the summer time setting starts
blinking.
5.
Press and release the upper right button
B
repeatedly to
change the target to be set.
• Each time you press button
B
, the target changes as follows:
Summer time Second Minute Hour 12/24-hour basis
• The summer time setting does not appear when selecting “UTC”.
6.
Adjust the target selected.
• Second: press button
A
in accordance with a reliable time source
• Minute/hour: rotate the crown. When you rotate the crown quickly, the
indication will change continuously. To stop the rapid change, rotate the
crown.
• 12/24-hour basis: press button
A
. Each time you press the button, the
setting changes alternately between 12H and 24H.
“A” (AM) or “P” (PM) is indicated when selecting 12-hour basis.
7.
Repeat steps 5 and 6 to set other targets.
8.
Push the crown in to position
0
to finish the procedure.
Setting the calendar
The calendar of this watch does not have to be adjusted manually until December
31, 2099 including leap years. (perpetual calendar)
1.
Push the crown in to position
0
.
2.
Rotate the crown to move the mode hand to point [CAL].
3.
Press and release the lower right button
A
or upper right
button
B
repeatedly to indicate an area name you want on the
area name display.
• For area names, refer to the table on “Using the world time”.
4.
Pull the crown out to position
2
.
“Month” blinks on the digital display.
5.
Press and release the upper right button
B
repeatedly to
change the target to be set.
• Each time you press button
B
, the target changes as follows:
Month Date Year
6.
Rotate the crown to set the calendar.
• When you rotate the crown quickly, the indication will change continuously.
To stop the rapid change, rotate the crown.
7.
Repeat steps 5 and 6 to set other targets.
8.
Push the crown in to position
0
to finish the procedure.
• The day of week is set automatically.
To Next Page
Need help?
General
