Citizen C650 - Initial Charging and Usage

2/4
C650/C651/C652 Abbreviated instruction
Using the world time
1.
Push the crown in to position
0
.
2.
Rotate the crown to move the mode hand to point [TME] or [CAL].
• When [CAL] is selected, the calendar is displayed.
3.
Press and release the lower right button
A
or upper right
button
B
to select an area.
The selected area and its time or calendar are indicated on the digital display
and the area name display.
Table of time zones and representative areas
Area name
Representative
area
Time
zone
UTC
Coordinated
Universal Time
±0
LON London
PAR Paris
+1
ROM Rome
CAI Cairo
+2
IST Istanbul
MOW Moscow
+3
KWI
Kuwait
DXB Dubai +4
KHI Karachi +5
DAC Dhaka +6
BKK Bangkok +7
SIN Singapore
+8HKG Hong Kong
PEK Beijing
Area name
Representative
area
Time
zone
TYO Tokyo +9
SYD Sydney +10
NOU Noumea +11
AKL Auckland +12
HNL Honolulu -10
ANC Anchorage -9
LAX Los Angeles -8
DEN Denver -7
MEX Mexico City
-6
CHI Chicago
NYC New York
-5
YUL Montreal
CCS Caracas -4
RIO Rio de Janeiro
-3
BUE Buenos Aires
• The time zone in the table is based on UTC (Coordinated Universal Time).
• Countries or regions may change time zones for various reasons.
Setting the summer time
You can set the summer time for each area.
• You cannot set the summer time for “UTC”.
1.
Push the crown in to position
0
.
2.
Rotate the crown to move the mode hand to point [TME].
3.
Press and release the lower right button
A
or upper right
button
B
repeatedly to indicate an area name you want to set
the summer time to.
4.
Pull the crown out to position
2
.
The second hand points 0 second and the summer time setting starts
blinking.
5.
Press and release the lower right button
A
.
• Each time you press button
A
, the summer time ON/OF(OFF) changes
alternately.
6.
Push the crown in to position
0
to finish the procedure.
Switching the time of analog and digital sections
The time of the analog section (hour/minute/24-hour hands) cannot be adjusted
directly.
Set the time of the area you want to indicate in the analog section once in the
digital section and then switch the time between the analog and digital sections.
• The second hand and the second indication displayed on the digital display are
always synchronized.
1.
Push the crown in to position
0
.
2.
Rotate the crown to move the mode hand to indicate [TME] or
[CAL].
• When [CAL] is selected, the calendar is displayed.
3.
Press and release the lower right button
A
or upper right
button
B
to select an area.
The time or calendar of the selected area is indicated on the digital display
and the area name display.
4.
Press and release both the upper right button
A
and lower
right button
B
at the same time.
The time of the digital and analog (hour/minute/24-hour hands) sections
switches.
Registering an area of a time zone you like
You can register one new area of a time zone on the world time of this watch.
• Check the time zone (based on the UTC) of the area you want to register
beforehand.
• The time zone can be set in 1 hour units.
1.
Push the crown in to position
0
.
2.
Rotate the crown to move the mode hand to point [SET].
3.
Pull the crown out to position
2
.
The area name and the time zone of the area previously set are displayed on
the area name display and the digital display.
• “---” is indicated when they have not been
set.
4.
Press and release the upper right button
B
repeatedly to
change the target to be changed.
• The target that is blinking is adjustable.
5.
Rotate the crown to set the target.
• Input alphabets and numbers to indicate the new area name. Following
letters, numbers and symbols can be used.
Alphabet: A to Z
Numbers: 0 to 9
Symbols: “--” (hyphens) and “ ” (blank spaces)
• The time zone can be set from “-11” to “+12”.
• When you rotate the crown quickly, the indication will change continuously.
To stop the rapid change, rotate the crown.
6.
Repeat steps 4 and 5 to set the area name and the time zone.
7.
Push the crown in to position
0
.
8.
Rotate the crown to move the mode hand to point [TME].
9.
Press and release the lower right button
A
or upper right
button
B
repeatedly to select the area newly registered.
Deleting the registered area
Set the area name to “---”.