EasyManua.ls Logo

Clas Ohlson EM6083 - User Manual

Clas Ohlson EM6083
5 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
English
GREAT BRITAIN customer service
tel: 08545 300 9799 e-mail: customerservice@clasohlson.co.uk internet: www.clasohlson.com/uk
Ver. 20130902
Digital Tyre Pressure Gauge
Art.no 40-8486 Model EM6083
Please read theentire instruction manual before use and save
it for future reference. Wereserve theright for any errors in text
or images and for making any necessary technical changes to
this document. Ifyou should have any questions concerning
technical problems please contact our Customer Services.
Safety
• The electronics and other components contained within
thepressure gauge cannot be adjusted or repaired.
Donotdismantle thepressure gauge.
• Never subject thepressure gauge to pressures exceeding
its rated upperlimit.
• When changing thebatteries, take care not to short-
circuitthem.
• The tyre pressure gauge must not be exposed to extreme
temperatures, moisture, vibrations or direct sunlight for
anextended period oftime.
Product description
• Digital tyre gauge with backlit LCD display.
• Measuring range: 0.3–6.8bar.
• Readings in bar, PSI, kPa or kg/cm².
• Extendable tread depthgauge.
• Automatic shut-off.
• 2×SR44/V357 batteries included.
Care and maintenance
Clean theproduct using asoft, moist cloth. Useamild detergent
and never use solvents or strong, abrasive cleaning agents for
cleaning as these can damage theproduct.
Disposal
This product should be disposed of in accordance with local
regulations. Ifyou are unsure how to proceed, contact your
local authority.
Buttons and functions
Battery replacement
The batteries should be changed when thedisplay isdim.
1. Turnthebattery cover anticlockwise and remove it.
2. Removetheold batteries.
3. Insert2 new SR44/V357 batteries with their negative
terminals facing downwards and then refit thebattery cover.
Note: Whenchanging thebatteries, take care not to short-
circuit them.
General advice
• It is wise to check your tyre pressure regularly. Thecorrect
tyre pressure will help ensure optimum fuel consumption,
improve road handling and reduce tyrewear.
• Always follow themanufacturer’s recommended tyre pressures
which are based on themeasurement of coldtyres.
• A tyre’s rated maximum pressure is often stated on itswall.
• On some models of car therecommended tyre pressures
can be found on thefuel filler cap.
Measuring thedepth oftread
• Press thedepth gauge button.
• The depth gauge has two fixed positions, one at 5 mm and
theother at 27mm.
• Insert thegauge into theshallowest groove of thetread and
measure thedepth.
Specifications
Measuring range 3.0–99.5PSI
0.3–6.8bar
20.7–686kPa
0.3–7 kg/cm²
Accuracy ± 1.5PSI
Resolution 0.5PSI
Units PSI, bar, kPa and kg/cm²
Automatic shut-off After 85 seconds
Batteries 2×SR44/V357, 1.5V
Operating temperature 0–50 °C
Storage temperature -10–55 °C
Size 135×80×32mm
Weight 60 g (incl. batteries)
Operation
1. Turn thegauge on using theon/off button. Thedisplay will
come on and after about 2 seconds “0.0.” will appear, to
indicate that thegauge is ready foruse.
2. The gauge sets automatically to theunit of measurement
that was used last. Theunit of measurement can be
changed by pressing theon/off button. Eachpress changes
theunit in thefollowing sequence: PSI bar kPa
kg/cm² PSI, etc.
1. On/off button – press
and release to turn
on, press and hold to
turnoff.
2. Nozzle.
3. LCD display – shows
thereading and selected
unit of measurement.
4. Battery compartment
(ontheback).
5. Treaddepth gauge
extend/retract control
button.
6. Treaddepthgauge.
3. Press thenozzle over thevalve of
thetyre. Makesure that thenozzle
forms anairtight seal over thevalve.
Listenfor any air escaping. Ifyou hear
ahissing sound, move thenozzle
alittle until theair stops escaping.
4. Wait for 2 seconds until thereading
on thedisplay has stabilized. Double-
check theunit of measurement and
take thereading.
5. The reading will be displayed for
85seconds before thepressure
gauge shuts off automatically. Ifyou
measure thepressure of another tyre
within 85 seconds, thenew reading
will be displayed.
6. Turn thepressure gauge off by
holding in theon/off button until
thedisplay turnsoff.
1
2
3
5
4
6
Question and Answer IconNeed help?

Do you have a question about the Clas Ohlson EM6083 and is the answer not in the manual?

Summary

Safety

Product Description

Care and Maintenance

Disposal

Buttons and Functions

Operation

Battery Replacement

General Advice

Measuring Tread Depth

Specifications

Summary

Safety

Product Description

Care and Maintenance

Disposal

Buttons and Functions

Operation

Battery Replacement

General Advice

Measuring Tread Depth

Specifications

Clas Ohlson EM6083 Specifications

General IconGeneral
CategoryMeasuring Instruments
TypeDigital Multimeter
DC Voltage Range200mV/2V/20V/200V/600V
AC Voltage Range200V/600V
Resistance Range200Ω/2kΩ/20kΩ/200kΩ/2MΩ
Diode TestYes
Continuity TestYes
Power SourceBattery
Battery9V (6F22)
Product NameEM6083
DisplayLCD
DC Current Range200μA/2mA/20mA/200mA/10A
Safety StandardCAT III 600V

Related product manuals