Clas Ohlson IK15P User Manual

English
a
b
c
d
e
f
g
h
i
j
k
l m n o p q
1
2
11
3
6 8
4
5
9
7
10
12
Ver.20231106
Solar-powered irrigation system
Art. no 31-6808 Model IK15P
Please read the entire instruction manual before using the product and then keep
it for future reference. We accept no liability for any errors in the text or images and
reserve the right to make any necessary changes to technical data. If you have
technical problems or other questions, please contact our customer service team.
Safety
• The product must not be immersed in water or other liquid.
• The product must not be covered in any way.
• You should check all the hoses and connections regularly.
• When you use the product for the first time, you should monitor it for a week to
make sure that everything is working correctly.
• Check all the connections, hoses and batteries and make sure that the program
is working correctly before you leave the product in operation for a long time
without monitoring it.
• Position the product the right way up. Never turn it upside down.
• The product must be repaired only by a trained service technician.
• The product contains parts that are sensitive to static electricity. If the product
does not function correctly, you may need to reset it by taking out the battery
and putting it back in again.
• Take care not to pull or jerk the hoses that are connected to the product.
Cleaning and care
• Clean the product by wiping it with a damp cloth. Use only mild cleaning agents.
Never use solvents or corrosive chemicals. Be careful not to damage the solar panel.
• If you are not going to use the product for a long time:
- Set the on/off switch to OFF.
- Remove the battery and store the product in a dry, frost-free location.
• Because the irrigation system is supplied with water from an open container,
there will inevitably be dirt in the water. Take the filter out and clean it regularly.
You may also need to take the system apart and clean the hoses and connections
occasionally during the watering season.
Specifications
Baeries 1×18650 Li-Ion 2600 mAh
Flow rao 45 litres/hour
Operang temp. 0 – 50°C
Dimensions
Irrigaon pump 122x115x70mm
Solar panel 206 × 168 × 20mm
Product description
Irrigation pump
a) Irrigation pump 1 pcs
b) Mounting plate 1 pcs
c) Solar panel 1 pcs
d) Mounting arm 1 pcs
e) Ground spike with
removable wall bracket 1 pcs
f) 1/4ʺ hose 15m
g) USB-C charging cable 1 pcs
h) Water level sensor 2.9m
i) Filter 1 pcs
j) Drip nozzle 15 pcs
k) Cable ties 3 pcs
l) Non-return valve 1 pcs
m) End cap 3 pcs
n) Straight coupling 5 pcs
o) Tee coupling 15 pcs
p) Cross connector 3 pcs
q) Screws 6 pcs
Package contents
1. LED display
2. [ +/ DELAY ]
3. [ – ]
4. Solar charging indicator
5. Solar panel port
6. [ OK/ ]
7. Water sensor inlet
8. Water leak indicator
9. Water in
10. Water out
11. Selector knob
- ON
- HOW OFTEN
- HOW LONG
- START TIME
- SET CLOCK
- OFF
12. Selector knob indicator
Installing the system
Decide where you want to set up the system. Make sure that you have a suitable
container for the water and that the plants you want to water are not too far away.
Note: The whole irrigation system should be positioned higher than the highest level
of the water in the container.
Solar panel – ground spike
1. Screw the mounting arm onto the ground spike.
2. Screw the mounting arm onto the bracket on the back of the solar panel.
3. Choose where you want to put the solar panel. Note: Do not put the solar panel
in a shady place.
4. Adjust the angle of the mounting arm for maximum exposure to sunlight.
Solar panel – mounting bracket
1. Unscrew the bracket from the ground spike.
2. Decide where you want to put the solar panel and screw the mounting bracket in
place. Note: Do not put the solar panel in a shady place.
3. Screw the mounting arm onto the mounting bracket.
4. Screw the solar panel onto the mounting arm. The screw must fit into the bracket
on the back of the solar panel.
5. Adjust the angle of the mounting arm for maximum exposure to sunlight.
Irrigation pump
1. Fix the mounting bracket in
a suitable location. Note:
Remember that the cable from
the solar panel must be able to
reach the pump.
2. Push the irrigation pump down
onto the mounting plate.
3. Connect the cable from the solar
panel to the solar panel port (5).
4. Connect the water level sensor to the water sensor inlet (7).

Clas Ohlson IK15P Specifications

General

Brand	Clas Ohlson
Model	IK15P
Category	Irrigation System
Language	English