CleanCraft HDR-K 48-15

Questions and Answers

K
Katie WilsonAug 20, 2025
What to do if CleanCraft Pressure Washer motor buzzes but fails to start?
- E
  Ethan LarsenAug 20, 2025
  If the CleanCraft Pressure Washer motor buzzes but doesn't start, it could be due to: * A power supply voltage that is too low. Check that the voltage of the mains power supply line is the same as that on the plate. * Voltage drop due to the use of an extension cable. Check the characteristics of the extension cable. * The appliance hasn't been used for a long period of time. * Problems with the TSS device.
K
kyle19Aug 22, 2025
What to do if CleanCraft Pressure Washer pump pressure drops suddenly during use?
- C
  Charles SmithAug 22, 2025
  If the CleanCraft Pressure Washer's pump pressure drops suddenly during use, it could be due to: * Water being sucked from an external tank. Connect the appliance to the mains water supply. * Inlet water being too hot. Reduce the temperature. * A clogged nozzle. Clean the nozzle. * A fouled inlet filter. Clean the filter.
D
daniellehunterAug 26, 2025
What to do if CleanCraft Pressure Washer motor fails to start?
- M
  Marvin ColeAug 26, 2025
  If the CleanCraft Pressure Washer motor fails to start, it could be due to: * No electrical power. Check that the plug is firmly in the socket and that the mains voltage supply is present. * Problems with the TSS device. * The appliance not being used for a long period of time. Using the tool unjam the motor through the hole at the rear of the appliance (in models with this feature).
J
Jeremiah MillerAug 28, 2025
Why is no detergent sucked in by my CleanCraft Pressure Washer?
- K
  Kathy GonzalezAug 28, 2025
  If your CleanCraft Pressure Washer is not sucking in detergent, consider the following: * The adjustable nozzle might be on a high-pressure setting. Set the nozzle on the " " setting. * The detergent might be too dense. Dilute it with water. * A high-pressure hose extension might be in use. Fit the original hose. * There may be deposits or a restriction in the detergent circuit. Flush with clean water and eliminate any restrictions.
A
armstrongkevinAug 31, 2025
Why is my CleanCraft Pressure Washer appliance noisy?
- H
  Helen ReynoldsAug 31, 2025
  If your CleanCraft Pressure Washer is noisy, it may be because the water is too hot. Reduce the temperature according to the technical data.
M
mwestSep 2, 2025
What causes water leakages in CleanCraft Pressure Washer?
- M
  Mary GonzalezSep 2, 2025
  Water leakages in the CleanCraft Pressure Washer may be caused by worn seals or the safety valve tripped and discharging.
D
David FarleySep 5, 2025
Why is water escaping from the thermostat valve of my CleanCraft Pressure Washer?
- H
  Heather HurstSep 5, 2025
  Water escapes from the thermostat valve of your CleanCraft Pressure Washer because the water temperature inside the pump head has exceeded the maximum rated value stated on the nameplate. With the appliance in operation, do not stop the water jet for more than 5 minutes at a time.
L
Lindsay ReyesSep 8, 2025
Why CleanCraft Pressure Washer starts even with gun trigger released?
- A
  Alexander DunnSep 8, 2025
  The CleanCraft Pressure Washer may start even with the gun trigger released if the high-pressure system or pump circuit is not watertight.
N
nwarrenSep 12, 2025
What causes oil leakages in CleanCraft Pressure Washer?
- T
  Tanya EnglishSep 12, 2025
  Oil leakages in the CleanCraft Pressure Washer are caused by worn seals.
D
Debra BlakeSep 13, 2025
Why CleanCraft Pressure Washer has no water delivery when gun trigger is depressed?
- S
  Shawn HaysSep 14, 2025
  The CleanCraft Pressure Washer may have no water delivery when the gun trigger is depressed because the nozzle is clogged. Clean the nozzle.