EasyManuals Logo

CO/Tech 36-4272 User Manual

CO/Tech 36-4272
5 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
GREAT BRITAIN • CUSTOMER SERVICE tel. 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk
Ver. 20150401
4 W LED Work Light
Art.no 36-4272
Please read theentire instruction manual before using theproduct and
then save it for future reference. We reserve theright for any errors in
text or images and any necessary changes made to technical data.
In theevent of technical problems or other queries, please contact
our Customer Services.
Safety
Do not subject thelight to knocks or shocks.
Thelight bulb cannot be replaced.
This product must not be dismantled or modified in any way.
Do not use theproduct if it or its charger is damaged in any way.
Only use thesupplied charger cables.
Operating instructions
Charging
Note: Charge thelight for 6–8 hours before using it for thefirst time.
Switch thelight off before charging it.
12 V
1. Connect the12V charger cable to thelight and then plug it into
the12V socket.
2. TheLED indicator shines red when thelight is being charged and
changes to green when thebattery is fully charged.
3. Unplug thecharger cable from thepower point when thebattery
is fully charged.
Care and maintenance
Clean theproduct using alightly moistened cloth. Use only mild
cleaning agents, never solvents or corrosive chemicals.
If thelight is not to be used for along time, thebattery should be
fully charged every 4 to 5 months to prolong its capacity.
Troubleshooting guide
Thelight does not
come on, theLED
indicator does not
flash blue.
Thebattery is flat, charge it.
Thelight won’t
charge. TheLED
doesn’t come on.
12V
Is thecharger cable undamaged and
securely connected to both the12V
socket and thelight?
Check that the12 V socket is live.
Sometimes thevehicle ignition needs
to be switched on in order for the12V
socket to be live.
Theplug of thecable contains a2Afuse
(20×5mm), check thefuse and change
it if necessary.
This is how to do it:
1. Unscrew thecap of theplug and remove
thefuse.
2. Replace thefuse with anew one.
3. Screw thecap back on.
230V
Is themains adaptor undamaged and
securely connected to both theelectrical
socket and thelight?
Is theelectrical socket is live?
230 V
TheAC/DC mains adaptor has
aninterchangeable plug for use
in different European countries.
To change theplug:
1. Press in thespring catch
and detach theplug from
theadaptor.
2. Slide thenew plug
onto theadaptor until
thespring catch locks it
in place.
3. Connect the230V mains adaptor to thelight and then plug it into
anelectrical socket.
4. TheLED indicator shines red when thelight is being charged and
changes to green when thebattery is fully charged.
5. Unplug themains adaptor from thepower point when thebattery
is fully charged.
Disposal
This product should be disposed of in accordance with local regulations.
If you are unsure how to proceed, contact your local council.
Specifications
LED 4 W COB
Luminous flux 200 lm
IP rating IP20
Rechargeable battery 7.2V/900mAh, NiMH
Mains adaptor In: 100–240 V, 50–60 Hz
Out: 12V DC, 300mA
Charging time 3–5 hours (6–8 hours before initial use)
Operating time Approx 3 hours
Operating temperature −5 to 40°C
Size Ø 57mm, height: 410mm
Weight 350g

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the CO/Tech 36-4272 and is the answer not in the manual?

CO/Tech 36-4272 Specifications

General IconGeneral
BrandCO/Tech
Model36-4272
CategoryWork Light
LanguageEnglish