Coleman 40-386 - User Manual

USER’S GUIDE
ATTENTION!
• Never try to open the case or remove its back cover.
• Do not operate buttons underwater
• Should moisture appear inside the watch, have it
checked immediately by your dealer. Moisture can
cause erosion of the metal parts of the watch.
• The watch is designed to withstand normal use.
Avoid dropping or otherwise abusing the watch.
• Avoid exposing the watch to extreme temperatures.
• Wipe the watch with a dry, soft cloth only. Avoid
direct contact with chemicals that can cause
deterioration of the plastic parts of the watch.
• Avoid wearing the watch in close proximity to
strong magnetic fields or static charge.
• Replacement battery type: CR 2025
BUTTONS
• Button operations are indicated using the letters as
shown in the illustration.

A. Backlight  C. Reset
B. Mode  D. Set
D. SetD. SetD. SetD. Set
DISPLAY
• The screen shown in display layout:

MODE SELECTION
• Press “B” to change modes in the following sequence:
a) Temperature mode
b) Timekeeping mode
c) Alarm mode
d) Stopwatch mode
e) Time setting mode

MODE INSTRUCTIONS
TEMPERATURE
• In temperature mode, press “D” to change from Celsius
to Fahrenheit, press “D” again to change it back.
Important:
• The temperature reading function measures ambient
temperature, not body temperature.
• Temperature reading may vary from ambient
temperature.
The expected range of variation is as follows:
 +/- 2 degrees Celsius
 +/- 4 degrees Fahrenheit
Environmental factors may produce larger variances.
Contact with body may result in greater variation. For
best results, remove watch from wrist and place in
location where temperature reading is desired. Leave for
up to 30 minutes.
• Temperature readings are updated every 10 minutes.
While updating, display may show -4˚ or -20˚. Pressing
the “D” button will reset to show reading.
• The watch may take up to 30 minutes to accurately
register large changes in temperature.
BACKLIGHT
• In any mode, press “A” to illuminate the display. The
backlight will stay on for 3 seconds.
TIMEKEEPING
• In timekeeping mode, Day and Date are displayed along
with Time.
• In timekeeping mode, press “D” to change from 12 Hour
to 24 Hour mode. Press again to change back.
• In 12 Hour mode, a “P” will indicate “PM”
• “24H” will indicate that the time is in 24 Hour mode.
ALARM
• The alarm sounds at the preset time each day for about
20 seconds each day. Press any button to stop it.
• In alarm mode, press “D”
Once: The alarm will be on and the chime will be off.
Twice: The alarm will be off and the chime will be on.
Three times: Both the alarm and the chime will be on.
Four times: Both the alarm and the chime will be off.
Look for “alarm” and “chime” icons on the display.
Setting the Alarm
• In alarm mode, press “C” until the hour flashes. Flashing
indicates that the hour is ready to be set.
• Press the “D” to change the hour. Press “D” and hold to
scroll through the numbers quickly.
• Press “C” set the hour and change the minutes.
• Press “D” to change the minutes. Press “D” and hold to
scroll through the numbers quickly.
• Press “C” to return to alarm mode.
"D"
"C"
"B"
"A"
Second
Minute
Temperature
Day
Hour
STOPWATCH
Lap Time
• In stopwatch mode, press “C” to reset to zero.
• Press “D” to start the stopwatch.
• Press “D” again to stop the stopwatch.
Split Time
1. In stopwatch mode, press “D” to start the
stopwatch.
2. Press “C” to display the split time. Stopwatch
continues timing internally
3. Press “C” again to clear the split time and continue
the measurement.
• Repeat steps 2 and 3 to measure multiple split times.
• Press “D” to stop the stopwatch.

Summary

Watch Buttons and Display

Button Identification

Identifies the watch buttons labeled A, B, C, and D for various operations.

Display Screen Layout

Details the screen layout showing Day, Temperature, Hour, Minute, and Second fields.

Mode Selection Sequence

Explains how to cycle through Temperature, Timekeeping, Alarm, Stopwatch, and Time Setting modes using the B button.

Detailed Mode Operations

Temperature Mode

Instructions for changing between Celsius and Fahrenheit and understanding temperature readings.

Backlight Function

Explains how to activate the display backlight for better visibility.

Alarm Mode and Setting

Covers alarm sound duration, stopping the alarm, and setting the alarm time.

Stopwatch Mode

Instructions for using the stopwatch for lap and split times.

Timekeeping Mode

Details displaying Day and Date, and switching between 12-hour and 24-hour time formats.

Time Setting Procedure

Setting Watch Time and Date

Step-by-step guide to setting seconds, hours, minutes, month, date, and day of the week.

Warranty and Return Information

Two Year Limited Warranty

Details warranty coverage, exclusions, and conditions for defects in materials and workmanship.

Return and Repair Instructions

Provides guidelines for returning or repairing the watch, including contact information and addresses.

Replacement Parts Price List

Lists prices for ordering replacement parts such as batteries, crystals, and bands.

Coleman 40-386 Specifications

General

Brand	Coleman
Model	40-386
Category	Watch
Language	English