Why is the scoreboard not working at all with my Colorado time systems GEN7?
If the scoreboard is not working, check the following: 1. Ensure the scoreboard has power and is turned on. 2. Make sure the scoreboard is not blanked. 3. Confirm the scoreboard cable is properly connected. 4. Inspect the scoreboard cable connectors for corrosion; clean or replace them if needed.
What to do if the start system does not start the race time on my Colorado time systems GEN7?
If the start system isn't initiating the race time, take these steps: 1. Ensure the start system cable is properly attached. 2. Clean the connectors. 3. Check the cabling. 4. Inspect the start system.
What to do if finish system pad or finish button hits are not registering on my Colorado time systems GEN7 Timer?
If the finish system pad or finish button hits aren't registering, consider the following: 1. Ensure the swimming software is ready for a pad hit and that the pad arm indicator is displayed in the appropriate lanes. 2. Verify that touchpad and button cables are properly and securely connected. 3. Clean the connectors. 4. Check the cabling. 5. Inspect the touchpad(s) or button(s).
How to fix Gen7 software unable to connect to Gen7 Timer by Colorado time systems?
If the Gen7 Software can't connect to the Gen7 Timer: 1. Check that the Ethernet cable is securely plugged into both devices. 2. If connecting via a switch or router, ensure that this device is powered on. 3. Ensure that your Windows networking settings match your timer settings. For most users, this will be the “Automatic Private IP Address” setting under “Alternate Configuration” under the “TCP/IP v4” properties of your Ethernet controller. 4. Consult your local IT department to see if any specific actions are needed to integrate your Gen7 into your facility network.
What to do if the interface (tablet or laptop) lost connection with the Colorado time systems GEN7 Timer?
If the interface (tablet or laptop) loses connection with the timer, the timer will continue running and will finish a race without the user interface. To restore the connection, check the cables and restart the software if necessary.
What to do if the scoreboard is not showing expected results with my Colorado time systems GEN7?
If the scoreboard isn't displaying the expected results: 1. Ensure the scoreboard cable is properly connected. 2. Check the scoreboard cable connectors for corrosion; clean or replace if necessary. 3. Verify that the scoreboard DIP switches for each module are set to the proper physical address. 4. Check the logical addresses in the Swimming software.
Why is the Event Sequence Download not working on my Colorado time systems Timer?
If the Event Sequence Download is not working: 1. Ensure the meet management cable is connected to the Meet Management port on the back of the timer.
What to do if I am not receiving the Event Sequence from meet management software on my Colorado time systems Timer?
If you're not receiving the event sequence from the meet management software: 1. Note that event sequences will not be received during a race; wait until the race is finished and the timer is ready for a new race. 2. Make sure the meet management cable is connected to both the meet management computer and the Meet Management port on the back of the Gen7 timer.
How to deal with unexpected behavior in lanes (numbering, lanes off, etc.) on Colorado time systems Timer?
If you're experiencing unexpected behavior in the lanes (numbering, lanes off, etc.), verify that the settings are correct for your pool for this session.
Important safety instructions for using the Gen7 power supply unit.
Describes two methods for connecting the start system to the Gen7 timer.
Details how to connect a computer to the Gen7 timer for control.
Information on connecting other equipment like touchpads and pushbuttons.
Steps to properly power on the Gen7 timer and interface computer.
Guides on creating new or opening existing meets and sessions in the software.
Explains the running time display and the functions of the toolbar.
How to print or export completed event results.
Navigates to the Race Data Screen to view past races.
Toggles backstroke start reaction on or off.
Options for setting the scoreboard display state.
Turn far end splits on or off during an event.
Posts race results in place order to the scoreboard.
Sets the order for Home and Guest display on numeric boards.
Opens a dialog to create new sessions or meets.
How to turn lanes on or off and how timing inputs are recorded.
Information on timer connection, status, and course settings.
Overview of settings navigation and toolbar functions.
Select between Light or Dark theme for the interface.
Choose the accent color displayed on all screens.
Adjusts the volume of beeps from the timer.
Enable or disable screen transition animations.
Sets touchpads or pushbuttons as the primary race finish mode.
Sets how start inputs are accepted for even/odd length races.
Enables or disables backstroke start reaction.
Notifies the operator of potential missed touches.
Sets how cumulative and subtractive splits are shown.
Adjusts the visibility duration of split times on the scoreboard.
Allows specific modules of the scoreboard to display race data.
Adjusts how lanes above 9 are displayed on the scoreboard.
Selects the paper size for printing race results.
Sets whether to show a preview before printing.
Sets the default printer for results.
Automatically prints race results upon reset.
Tools for adding, deleting, moving, and clearing events.
Adjusts an event's number in the sequence.
Sets who will be competing in the event.
Sets the race distance for the event.
Sets the stroke type for the selected event.
Adjusts meet name, start/end dates, and governing body.
Sets the desired course for the session (e.g., 25-yard, 50-meter).
Determines how lanes are mapped to the timer (normal or reversed).
Turns lanes on or off for a session.
Adds information for records displayed in the Records section.
Selects the number of lanes available in the pool.
Toggles the first lane numbering between 1 or 0.
A step-by-step guide using a sample race scenario.
Steps to start a race using the Gen7 timer and start system.
How to handle a missed touch and its impact on length count.
How to correct an extra touch registered by a touchpad.
Prepares a lane for an upcoming finish touch.
How to set a lane as a 'no show' and its display.
Procedures for disqualifying a swimmer and its indicators.
How to clean cable connectors on the back panel.
How to clean the Gen7 case.
How to clean cable and in-deck connectors.
How to ensure connectors fit and check for corrosion.
How to ensure connectors fit and check for corrosion.
Environmental operating conditions and limits for the Gen7 timer.
Electrical specifications including power supply and battery.
Details of various input and output ports on the Gen7 timer.
Guidelines for installation and maintenance of the Gen7 timer.
General| Brand | Colorado time systems |
|---|---|
| Model | GEN7 |
| Category | Timer |
| Language | English |
To Next Page
