EasyManua.ls Logo

COMAC INNOVA 60 B 2013 - User Manual

COMAC INNOVA 60 B 2013
84 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
USE AND MAINTENANCE MANUAL
INNOVA 60 B 2013
INNOVA 65-75-85-100 B 2013
INNOVA 70 S 2013
ED. 07-2013 EN
ORIGINAL
INSTRUCTIONS
Doc. 10029401
AC Version

Table of Contents

Questions and Answers

  • K
    kristinacoxAug 17, 2025
    How to fix insufficient water on brushes COMAC Cleaning Equipment?
    • K
      Kristen DuncanAug 17, 2025
      To address insufficient water on the brushes of your COMAC Cleaning Equipment, start by ensuring the solution tank has water, which can be checked via the level tube on the front left of the seat. Then, verify that the detergent solution tap is open and the knob on the back of the steering column is completely lowered. If equipped with CDS, check that the water and detergent flow in the water system are not at zero by pressing buttons (03) and (04) respectively. Also, clean the solution filter at the front of the machine and ensure the water distribution pipe (05) on 'S' versions is not blocked. For Innova 60B versions with 'KIT WATER MANAGEMENT', confirm that the choke bushing is not blocked.
  • J
    Joseph PageAug 20, 2025
    Why squeegee does not dry perfectly COMAC INNOVA 60 B 2013?
    • J
      John TaylorAug 20, 2025
      If the squeegee on your COMAC Cleaning Equipment isn't drying perfectly, start by checking if the squeegee is clean. Next, review the squeegee adjustments. Clean the entire vacuum unit, and replace the rubber blades if they are worn out. Finally, ensure the cap on the recovery tank drainage hose is properly closed.
  • K
    Kenneth HudsonAug 22, 2025
    What to do if brush motor does not work COMAC INNOVA 60 B 2013?
    • B
      Bailey HendersonAug 22, 2025
      If your COMAC Cleaning Equipment's brush motor isn't working, ensure the brush head is lowered during start-up. Confirm the operator is properly seated. For Innova 65B, 75B, 85B, 100B, 70S, and 70BTO versions, check that the I-DRIVE selector is on 'C' or 'D'. Also, verify that no thermal protection device has intervened and that the motor is correctly connected to the terminal board under the footboards.
  • J
    Jorge HarrisAug 26, 2025
    Why the machine does not clean well COMAC INNOVA 60 B 2013 Cleaning Equipment?
    • B
      brendangonzalezAug 26, 2025
      If your COMAC Cleaning Equipment isn't cleaning well, inspect the brushes for wear and tear, and replace them if necessary. Brushes should be changed when the bristles are about 15 mm long. Consider using a different type of brush designed for more resistant dirt, available upon request.
  • C
    Chelsey Rosales DDSAug 28, 2025
    Why excessive foam production COMAC INNOVA 60 B 2013?
    • D
      Denise JonesAug 28, 2025
      If your COMAC Cleaning Equipment produces excessive foam, ensure a low foam detergent is used. If needed, add a small amount of anti-foam liquid to the recovery tank. Remember that when the floor isn't very dirty, more foam is generated, so dilute the detergent solution more.
  • R
    Ronald SchroederAug 31, 2025
    What to do if brush motor doesn't work (INNOVA 60B versions) COMAC INNOVA 60 B 2013 Cleaning Equipment?
    • F
      Frank MooreAug 31, 2025
      If the brush motor on your Innova 60B version COMAC Cleaning Equipment isn't working, make sure the brush head is lowered during forward movement by turning the right lever clockwise. Also, ensure the operator is properly seated. Check that no thermal protection device has intervened and that the motor is correctly connected to the terminal board under the footboards.
  • C
    cynthia41Sep 2, 2025
    Why vacuum cleaner does not function COMAC INNOVA 60 B 2013 Cleaning Equipment?
    • W
      William CurtisSep 2, 2025
      If the vacuum cleaner on your COMAC Cleaning Equipment isn't functioning, check if the recovery tank is full and empty it if necessary. Also, inspect the float on the vacuum cap to ensure it's working properly.
  • L
    Luis KingSep 5, 2025
    Why the machine does not start COMAC INNOVA 60 B 2013 Cleaning Equipment?
    • A
      Adam RoachSep 5, 2025
      If your COMAC Cleaning Equipment won't start, verify the connector is connected to the batteries. Check that the key switch is on 'I', and ensure the batteries are charged by checking the symbol on the control display.
  • O
    owagnerSep 8, 2025
    What to do if it is impossible to raise or lower the brush head or squeegee COMAC Cleaning Equipment?
    • S
      Sean FrenchSep 8, 2025
      The COMAC Cleaning Equipment is fitted with electrical protection devices that control the brush head and squeegee ascent/descent motor reducers. If you cannot raise or lower the brush head or squeegee, and suspect overloading, switch the machine off and on again to reset the fuses. If the problem continues, contact the specialist technical assistance centre.
  • M
    merrittjoySep 12, 2025
    What to do with electric fuses and thermal cut-outs COMAC INNOVA 60 B 2013 Cleaning Equipment?
    • A
      Alex BurkeSep 12, 2025
      The COMAC Cleaning Equipment is fitted with self-restoring safety fuses that interrupt power to the brush and vacuum motor when the machine is overloaded. If electric fuses and thermal cut-outs are activated, switch off the machine and wait about 40 seconds for the fuses to cool down. If the switch disconnects the current repeatedly, contact the specialised technical assistance centre.

COMAC INNOVA 60 B 2013 Specifications

General IconGeneral
BrandCOMAC
ModelINNOVA 60 B 2013
CategoryCleaning Equipment
LanguageEnglish