EN
User instructions
Q1 S3H2 H3S9
1
2
2.1 WASHING PHASES RC
2.1.a Switching on and Preparing the machine
To switch on the machine, press the power switch (Q1)
the internal signaler to the switch it becomes red.
The lamp (H3) remains lit for a few seconds
The boiler, and then the tank, will start to ll automa-
tically.
Once the water level has been reached, the heating
elements will switch in, rst in the boiler, then in the tank.
Once the water in the tank reaches the correct tempera-
ture, the tank temperature lamp (H2) will be FIXED lit.
During the whole duration of the cycle the lamp (H3)
remains ON.
WASHING OPERATION
If not using the equipped automatic dosing system, pour
into the tank a quantity of detergent suitable for the volu
me and hardness of the water. For quantities, refer to the
specic instructions for the detergent in use.
To repeat the operation every 4 cycle.
ATTENTION
When items to be washed are encrusted with burnt
on matter, or a long time has passed between use
and washing, it is essential to carry out a pre-was
soak using a suitable softening agent.
The use of hand-washing products is to be avoided
as they could produce foam inside the machine.
IMPORTANT
It is advised to install a detergent pump automatic
rie (to see paragraph 3,2).
Place the basket of items to be washed inside the ma-
chine, having rst removed any solid waste.
2.1.b During of Cycle
The duration of the washing cycle is FIXED :
CYCLE = 90 sec.
CYCLE = 120 sec.
To cycle through 1 or 2, press the key cycle selection (S9).
The start of the cycle is set AUTOMATIC
(with the opening and closing of the hood).
TEMPERATURE READING
(only models prepared)
The temperatures are shown on the display D1
of the water contained in the tank and in the boiler
2.1.c STARTING WASHING CYCLE
IMPORTANT
The selection of starting MANUAL or AUTOMATIC
cycle must be made by an authorised technician.
STARTING MANUAL WASH CYCLE
To start the wash cycle in MANUAL mode the cycle
start mode must be changed.
IMPORTANT
This operation must be carried out by an authorised
technician during installation..
STARTING MANUAL WASH CYCLE
To start the washing cycle, press the (S3) button.
Throughout the washing cycle the lamp (H3) will be
FIXED lit.
The use of the machine ensures rinsing at the ideal
temperature for hygienic purposes every time;
Indeed, if the temperature is not sufcient the wash will
be automatically prolonged so as to ensure the neces-
sary conditions of optimum rinsing at 85 °C.
The waiting time required to attain optimum temperature
can extend to a maximum of 8 minutes.
Finished the time max of 8 min, the (H3) cycle lamp will
FLASH RAPIDLY until the end of the cycle. To reset the
ashing (anomaly signalling), switch the machine off
and back on using the power switch (Q1) .
2.1.d Interrupting the cycle
1) It is possible to interrupt the washing cycle momen-
tarily by opening the hood (the lamp H3 will FLASH):
this is an EMERGENCY measure:
On closing the hood, operations will resume from the
point in which they stopped.
2) The cycle can also be interrupted by SWITCHING
the machine’s power switch (Q1); the internal signaler
to the switch it became GREEN.
Allow items to dry and remove them from the basket
with clean hands.
Store all items on hygienic and completely stable sur-
faces.
2.1.e Manual Draining
It is possible to drain the water from the tank at any time
during the day, according to the waste accumulated.
To carry out this operation, proceed as follows:
- SWITCH the machine’s power switch (Q1); the internal
signaler to the switch it becomes GREEN and release
the overow, allowing all the water to drain from the tank;
- Remove the tank lter (14) and clean;
30
To Next Page
Loading...
Need help?
General
