EasyManuals Logo

Comet MTP MC 18 User Manual

Comet MTP MC 18
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #26 background imageLoading...
Page #26 background image
26
MOTOR PUMP IDENTIFICATION PLATE
WARNING
•Shouldtheidenticationplatedeteriorateduringuse,contacttheManufacturerora
Skilled Technician
to
haveitrestored.
eidenticationplate(12)showsthemotorpumpmodel,theserialnumber,theyearofmanufactureandthe
mainelectricalandmechanicalspecications(maxrotationspeed,maxpressure,weight,powersupplyvoltage,
input,etc.).Itislocatedonthebaseofthemotorpump(allversionswithcombustionengine,MTPMC20/20
andMTPMC25withelectricmotor),oronthepowerbox(remainingmotorpumpswithelectricmotor).
SAFETY DEVICES
WARNING
•emachineinwhichthemotorpumpisintegratedmustalwaysfeatureasafetyvalve,i.e.,amaxpressure
valve,suitablycalibrated,whichdischargesexcesspressureincaseofafaultinthehigh-pressurecircuit:inthe
eventofthesafetyvalvetrippingfrequently,immediatelystopusingthemachineinwhichthemotorpumpis
integratedandhaveitcheckedbya
Skilled Technician
.
a) Pressure unloader/regulation valve.
isvalveissuitablysetbytheManufacturerandallowsregulatingtheoperatingpressureandpermitsthe
pumpeduidtoowbacktowardsthebypassduct,thuspreventingtheaccumulationofdangerouspressures
whenthedeliverylineisclosedorwhenattemptsaremadetosetpressurevaluesabovethemaximumones
allowed.Apressureunloader/regulationvalvefeaturingpumpedliquidon/odevices(suchastaps)isusually
called
control unit
.
WARNING
•epressureunloader/regulationvalveisseteitherbythemotorpumpManufacturerorbythatofthemachine
inwhichthemotorpumpisintegrated.
Never try and adjust the pressure unloader/regulation valve to
alter the setting: only operate on this by means of the knob(3).
b)
ermal or ampere cut-out protection device.
isdevicestopsmotorpumpoperationintheeventofoverheatingoftheelectricmotororexcessivepower
absorption respectively.
Ifoneofthesetrips,proceedasfollows,
keeping to the indications shown in the manual of the machine in
which the motor pump is integrated:
• stopthemachineandremovetheplugfromthepowersocket;
• releaseanyresidualpressureinthehigh-pressurecircuit;
• wait10÷15minutesforthemotorpumptocooldown;
• makesuretheinstructionshavebeenfollowedintheparagraph
“checkIng and connectIng up to the power
supply
,withspecialreferencetoanyextensionused;
• ttheplugbackinthesocketandrepeatthestartprocedure.
WARNING
•Incasethesesafetydevicestripfrequently,donotusethemotorpump(andthereforethemachineinwhichit
isintegrated)withoutrsthavingitcheckedbya
Skilled Technician
.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Comet MTP MC 18 and is the answer not in the manual?

Comet MTP MC 18 Specifications

General IconGeneral
BrandComet
ModelMTP MC 18
CategoryWater Pump
LanguageEnglish

Related product manuals