Competition Pro TL-1022 User Manual

OWNER’S MANUAL
All content © Copyright TheLoudest.com 2006
Technical Specifications
Output power
(14.4v)
1 x 4000 Watt Max @ 1 ohm
1 x 1500 Watt RMS @ 1 ohm (THD+N < 2.5%)
1x 950 Watt RMS @ 2 ohm (THD+N < 2%)
1 x 600 Watt RMS @ 4 ohm (THD+N < 1%)
Output power
(Two TL-1022 amplifiers bridged)
Not possible @ 1 ohm
1 x 3000 Watt RMS @ 2 ohm
1 x 1800 Watt RMS @ 4 ohm
Frequency response 10 Hz ~ 200 Hz
Subsonic Filter Frequency Range 20 ~ 50 Hz (Adjustable)
Low Pass Filter Frequency Range 40 ~ 180 Hz (Adjustable)
Bass Boost Frequency Range 45 Hz
Input Impedance 67 Kohm
Input sensitivity 0.2 V ~ 5 V
Signal/Noise Ratio (A. Wtg)
1 Watt Reff.
>100 dB
Damping Factor (100 Hz @ 4 ohm) >120
Efficiency 82%
Idle Current 1.2 A
Max Peak Current 120 A
Minimum Subwoofer impedance Using one TL-1022: 1 ohm
Using two TL-1022s: 2 ohm
Power supply DC 12V
Dimensions:
(length x width x height)
58 x 210 x 377 mm
Features
 Class D monoblock subwoofer amplifier
 Huge power output
 Subsonic, Lowpass and bass boost filters
 Continuously adjustable phase control from 0 to 180 degrees
 N-Channel Circuit for high efficiency
 Excessive heat, Reverse polarity, Short circuit and Input overload protection
 Heavy-duty power supply
 Heavy-duty aluminium heatsink
 “Bass Kompressor” circuitry provides extra low-frequency enhancement
 Easy bridging of two TL-1022 amplifiers
OWNER’S
MANUAL
HIGH PERFORMANCE
CLASS D MONOBLOCK
SUBWOOFER AMPLIFIER
4,000 Watts Max @ 1 ohm
1,500 Watts RMS @ 1 ohm
SAFETY GUIDELINES | TECHNICAL SPECIFICATIONS
FEATURES | INSTALLATION AND OPERATION INSTRUCTIONS

Competition Pro TL-1022 Specifications

General

Brand	Competition Pro
Model	TL-1022
Category	Amplifier
Language	English

Summary

Introduction

Control Panel Functions

Indicators

LED indicators for power and protection status, detailing potential fault conditions.

Remote Gain

Socket for connecting the Remote Gain Controller for adjustable output level from the vehicle cabin.

Audio Input

RCA sockets for connecting a line-level audio source unit, recommending shielded cables.

Bridge In/Out

RCA sockets used for connecting two TL-1022 amplifiers together for bridging.

Gain Control

Knob to adjust amplifier volume, proportional to source unit signal level for optimal output.

Low Pass Filter (LPF) control

Adjustable filter (40-180 Hz) to set the highest frequency sent to the subwoofer for optimal bass response.

Phase

Control for adjustable signal phase lag (0-180 degrees) to optimize subwoofer integration with vehicle acoustics.

Subsonic Filter

Adjustable filter (5-50 Hz) to set the lowest frequency sent to the subwoofer, optimizing efficiency.

Bass Boost

Control to boost bass frequencies around 45 Hz by up to 12 dB.

Speaker Connections

Screw terminals for connecting subwoofer speaker cables, with bridging configuration notes.

Power Connections

Terminals for connecting 12V positive, negative/earth, and remote/ignition wires.

Mounting Instructions

Installation

Power, Alternator, and Battery Considerations

Discusses upgrading vehicle alternator, battery, and considerations for high current draw.

Wiring Kit and Fuse

Recommends the TL-1102 wiring kit and minimum fuse requirements for installation.

Disconnecting Vehicle Battery

Advises disconnecting the negative battery terminal before installation for safety and to prevent alarms.

Bridging

Bridging Two TL-1022 Amplifiers

Instructions and diagram for connecting two TL-1022 amplifiers together in a master/slave configuration.

Safety

Health Warning

Warns about potential physical side effects of listening at high powers, including hearing loss.

General Safety

Advises on safe driving practices regarding loud music and precautions for cleaning and installation.

Troubleshooting