Need help?Do you have a question about the Consilium CFD5000 FDS and is the answer not in the manual?
General| Brand | Consilium |
|---|---|
| Model | CFD5000 FDS |
| Category | Fire Alarms |
| Language | English |
Explains manual purpose, lists related documents, and defines safety symbols.
Details compliance with industry standards like SIL 2 and RAMS for the CFD5000 T system.
Actions for alarms, safety measures, ESD precautions, and system operation.
Overview of CFD5000 FDS, CCP Fire, and system interfaces.
Details the CFD5000 FDS as an extension, its interfaces, and modules.
Describes the FDS subsystem, module types, and loop-line configurations.
Explains system interfaces, SSP Bus, and IDAxt communication protocols.
Lists CFD5000 modules and explains power supply requirements.
Overviews other modules and references control panel instructions.
Guides on handling alarms, resetting, disabling, and reconnecting items.
Describes the control panel layout, indicators, and operational controls.
Details how to navigate the menu system and lists top-level menu options.
Describes menu items for alarms, disablements, login, settings, and history.
Explains navigation within specific menu sections for alarms and disablements.
Details options for disabling zones and detectors/call points.
Describes menu items for system access, service, and event history.
Explains Service Menu features and History menu event lists.
Explains detector condition checking and system access level importance.
Details access level permissions and procedures for setting system time and date.
Information displayed during fire alarms and procedures for resetting alarms.
Details fault alarm display and initial fault handling procedures.
Procedures for resetting faults and understanding warning messages.
Information on disablements, indicators, and acknowledgement.
Step-by-step guide for disabling zones and specific detectors/call points.
Procedures for reconnecting items and overview of the Service Menu.
Instructions for saving system and BIST logs to USB for analysis.
Guide on how to report a fault, including necessary information and log files.
General introduction and description of repeater panel keys, indicators, and modes.
Explains mode settings (Day/Night) and the lamp test function.
Introduction to fault codes, system identification, and remediation warnings.
Lists fault codes for communication, module defects, and firmware problems.
Lists fault codes for loop unit connection, contact, and cable faults.
Lists fault codes for sensor defects, external power, and position faults.
Lists fault codes for cable breaks, communication errors, and address conflicts.
Lists fault codes for earth faults, emergency power, battery charger, and external equipment.
Lists fault codes for PSU faults, configuration errors, and mains power loss.
Lists fault codes for internal faults, high resistance, low voltage, and bus issues.
Lists fault codes for incompatible modules, wrong unit types, and configuration errors.
Lists fault codes for current limits, charging issues, and PSU voltage.
Lists fault codes related to PSU voltage levels and configuration.
Lists fault codes for XFIRE signal, overheating, and low voltage on backbone channels.
Lists fault codes for application issues, relay outputs, airflow, and service time.
Provides definitions and abbreviations for terms used in the fire detection system manual.
Continues defining terms such as APF, ASP detector, Backbone Bus, and BIST.
Continues defining terms like Central, Charger M, Configuration File, and Control modules.
Continues defining terms like CS-PYH, DCS, Detector, DIP switch, and Disablement.
Continues defining terms like I/O Module, IDA, IEC 62280-2, and Inter-central communication.
Continues defining terms like LRU, Managed mode, MCP, and Module.
Continues defining terms like Safe State, Safety Controller, Safety Integrity, and Salwico Language.
Continues defining terms like USB, Warning Condition, and Zone.
Explains how to update the Consist ID using a USB memory stick and CS-Com M module.
Details the Consist ID update process and CS-Com M mode indications.
Further details on Consist ID update and SDTv2 channel status indications.
Shows possible combinations for software versions for modules and loop units.
Provides a comprehensive compatibility matrix for software versions.
To Next Page