Continental Access CICP18ACCNETBD - User Manual

1
CICP18ACCNETBD Ethernet Board
Installation Instructions
For Superterm and Accelaterm Control Panels
FOR SUPERTERM INSTALLATIONS:
The CICP18ACCNETBD Ethernet board is mounted in the
CICP18ACCBD Accelerator board (see installation instructions
WI1593 for more information regarding the installation of the
CICP18ACCBD Accelerator board).
Note: For best performance, one CICP18ACCNETBD Ethernet
board should be installed in each CICP18ACCBD accelerator
board in each control panel. However, one CICP18ACCNETBD
Ethernet board connection may be shared (networked) with up to
63 other Accelerator-equipped Superterm panels. See WI1073 for
more information regarding Superterm network configurations.
Prior to opening the Ethernet board package or
touching anything inside the control panel enclosure,
discharge any static electricity from your body or
clothing. Use a grounded wrist strap or touch an
unpainted, grounded metal object such as the metal
frame of the panel enclosure.
INSTALLATION
1. Find the MAC address located on the
white label wrapped around the
Ethernet plug (circled in Fig. 1 at
right). Write the MAC address here:
_______________________ and
keep this paper in a safe location for
future reference.
2. Before installation, verify that the panel and Accelerator board
are both working correctly. Verify that both the OK lamp
(LED) on the Accelerator board and the heartbeat lamp on the
motherboard (location T1) blink in unison once per second.
Verify the MEMORY BACKUP CELL jumper is in the IN
position providing memory data retention.
3. Inside the panel housing, remove power from the main control
panel PCB by pushing the POWER plug connector (located
on the lower right of the PCB) downward until the connector
is completely separated from the PCB. Do not disconnect the
battery wires. See Fig. 2, below (left).
4. Align the board:
Use the image in Fig. 3 (above) to find the
Ethernet board mounting location near the top of the
CICP18ACCBD Accelerator board. Carefully align the two
Ethernet board snap-lock standoffs with the two Accelerator
PC board mounting holes. Then align the Ethernet board plug
with the Accelerator board receptacle (JP4) as shown below.
Insert the board:
With both standoffs and the plug aligned,
firmly press the Ethernet board into the Accelerator board by
squeezing the Ethernet board receptacle. Use your fingers to
hold the accelerator board while squeezing the Ethernet board
as shown Fig. 4.
CONTINENTAL ACCESS LLC
A NAPCO SECURITY GROUP COMPANY
355 Bayview Avenue, Amityville, NY 11701
Phone: 631-842-9400 Fax: 631-842-9135
www.cicaccess.com
Publicly traded on NASDAQ Symbol: NSSC
© NAPCO 2013
Fig. 2: Push POWER plug connector downward until removed
Power plug
Power socket
WI1595A 06/13
Fig. 3: Align the two snap-lock standoffs and plug with the Accel-
erator board holes and receptacle
Receptacle "JP4"
Plug
Two standoffs
Mounting holes
Fig. 4: Squeeze to insert the board
Squeeze Here
Receptacle
Squeeze Here
Fig. 1: MAC address location

Summary

FOR SUPERTERM INSTALLATIONS

Safety Precautions

Discharge static electricity from your body or clothing before handling components.

INSTALLATION

Record MAC Address

Locate and write down the MAC address from the Ethernet plug's white label.

Verify System Status

Check OK and heartbeat lamps, and MEMORY BACKUP CELL jumper position.

Disconnect Panel Power

Remove the POWER plug connector from the main control panel PCB.

Align and Mount Board

Align Ethernet board standoffs and plug with Accelerator board holes and receptacle.

Insert Ethernet Board

Firmly press the Ethernet board onto the Accelerator board receptacle.

Connect Ethernet Cable

Insert CAT5/6 Ethernet cable through clamp and knockout, pull to length.

Apply Shielding

Secure silver braided shield to clamp and cover cable for grounding.

Secure Cable and Shield

Ensure shield covers cable, leaving 1 inch exposed. Do not cover plug.

Reconnect Power

Re-connect POWER plug and verify OK/heartbeat lamps blink correctly.

FOR ACCELATERM INSTALLATIONS

Safety Precautions

Discharge static electricity from your body or clothing before handling boards.

INSTALLATION

Record MAC Address

Locate and write down the MAC address from the Ethernet plug's white label.

Verify Panel Operation

Confirm the Accelaterm control panel is functioning correctly.

Disconnect System Power

Disconnect power to the system, including the battery wires.

Align and Mount Board

Align Ethernet board standoffs and plug with Interface board holes and receptacle.

Insert Ethernet Board

Press Ethernet board firmly into the Interface board by squeezing receptacle.

Connect Ethernet Cable

Insert CAT5/6 Ethernet cable through clamp and knockout, pull to length.

Apply Shielding

Secure silver braided shield to clamp and cover cable for grounding.

Secure Cable and Shield

Ensure shield covers cable, leaving 1 inch exposed. Do not cover plug.

Reconnect Power

Re-connect power and verify OK/heartbeat lamps blink correctly.

Continental Access CICP18ACCNETBD Specifications