Continental Access SUPERTERM CIC1800 - User Manual

92 pages

Save Page as PDF

To Next Page

SUPERTERM

CIC1800 / CICP1400UL

Access Control Unit

Installation and Service Manual

Version 1

A NAPCO SECURITY TECHNOLOGIES COMPANY

355 Bayview Avenue, Amityville, NY 11701

Phone: 631-842-9400 Fax: 631-842-9135

www.cicaccess.com

Publicly traded on NASDAQ Symbol: NSSC

WI 1073CLF 5/19

Main Page

Default Chapter4
- Table of Contents4
Description7
4-Door Version7
Regulatory Considerations8
- Regulatory Considerations for Superterm Installations8
- Installer Responsibilities (General)9
- Installer Responsibilities UL294 General9
Configuration10
- Standard Version10
- Expanded Version10
- Memory Configurations10
- Expansion Boards and Accessories11
- Memory Expansion11
- Digital Input/Digital Output (D1/DO) Board11
- Supervised Alarm Board11
- Battery Backup11
- Power Transformer11
Installation12
- About this Manual12
- Installation Preparation13
- Cabinet Mounting14
- Cable Routing15
- Incoming Power Conduit Knockout15
- Accessory Conduit Knockouts15
- Grounding Accessory Drain and Shield Wires15
Power Connections16
- AC Power Source Grounding16
- 120VAC Power16
- Superterm Circuit Board Layout17
- Step-Down Transformer Connection18
- Power Input Terminal Strip Jumpers18
- Battery Backup Connection18
- Expansion Power Supply Connection19
Door Connections20
- Wiegand/Proximity Reader Connections20
- Wiegand/Proximity Reader Cable Requirements20
- Magnetic Stripe Reader Connection22
- Magnetic Stripe Reader Cable Requirements22
- Keypad Connection23
- Keypad Cable Requirements23
- Door Status Sensor Connection24
- Door Status Sensor Cable Requirements24
- Request-To-Exit (Bypass) Sensor Connection25
- Request-To-Exit Sensor Cable Requirements25
Relay Connections26
- Description26
- Door Strike Relays26
- Auxiliary Relays26
- Console Relay26
- Relay Characteristics26
- Door Strike Relay Operation28
- LOCAL Power Connection30
- Emergency Sensor Connection30
- LOCAL Power Door Strike Connection32
- Door Strike Relay Connection - Normally Open32
- Door Strike Relay Connection - Normally Closed32
- REMOTE Power Mode34
- Door Strike Relay Connection - Normally Open34
- Door Strike Relay Connection - Normally Closed34
- Auxiliary Relay Connection34
- Auxiliary Relay Power Requirements34
- Auxiliary Relay Connection - Normally Open (NO)34
- Aux Relay Connection - Normally Closed (NC)34
Auxiliary Power36
- Additional +12VDC Power Outlets36
Alarm Connection38
- Supervised Alarms38
- Configuring an Alarm in the Supervised Condition38
- Alarm Cable Requirements38
- Tamper Switch38
Communication Connection40
- RS-232 Communications - Host Computer/Modem40
- RS-232 Cable Requirements40
- RS-232 Jumper Settings40
- Address Setting40
- Superterm to Host Computer/Modem Connection40
- Networking42
- Network Jumper Settings42
- Network Cable Requirements42
- Network Address Settings42
- RS-232 to RS-422 REPEAT Network44
- RS-232 to RS-422 REPEAT Jumper Setting44
- RS-232 to RS-422 REPEAT Drain Wires44
- RS-232 to RS-422 MULTIDROP Network46
- RS-232 to RS-422 MULTIDROP Drain Wires46
- RS-232 to RS-422 MUTIDROP Jumper Setting46
- RS-422 to RS-422 REPEAT Network48
- RS-422 to RS-422 REPEAT Drain Wires48
- RS-422 to RS-422 REPEAT Jumper Setting48
- RS-422 to RS-422 MULTIDROP Network50
- RS-422 to RS-422 MULTIDROP Drain Wires50
- RS-422 to RS-422 MULTIDROP Jumper Setting50
- Auxiliary Communications Channels52
- COM1 Terminal Strip Connection52
- Printer Cable Requirements52
- Printer Setup Parameters52
- COM2 Terminal Strip Connection54
- RS-232 Cable Requirements54
- XTM Terminal Strip Connections54
- RS-485 Cable Requirements54
Expansion Board Connections56
- Expansion Input/Output Boards56
- Supervised Alarm Board Installation58
- Supervised Alarm Board Power Connection58
- Supervised Alarm Board Power Cable Requirements58
- Data/Control Line Ribbon Cable Connections58
- Supervised Alarm Board Accessory Connections60
- Supervised Alarm Cable Requirements60
- Supervised Alarm Board Address Selection Jumper60
- Setting the Address Selection Jumper60
- DI/DO Board Connection62
- DI/DO Board Power Cable Requirements62
- Data/Control Line Ribbon Cable Connections62
- DI/DO Alarm Input Connections64
- DI/DO Alarm Cable Requirements64
- DI/DO Alarm Output Connections66
- DI/DO Alarm Board Address Selection Jumper66
- Setting the Address Selection Jumper66
I/O Signal Mapping68
- Superterm Main Circuit Board: 8-Reader Version68
- Superterm Main Circuit Board: 4-Reader Version69
- Expansion I/O Boards70
- DI/DO Board70
- Supervised Alarm Board71
Settings72
- Jumper Settings72
- 232-1 Jumper72
- EOL1 Jumper72
- EOL2 Jumper72
- COM1 Jumper74
- COM2 Jumper74
- MONITOR Jumper74
- MBAT Jumper76
- MODE1 Jumper76
- Door Strike Jumper Setting78
- LOCAL Power Jumper Setting78
- REMOTE Power Jumper Setting78
Troubleshooting80
- LED Diagnostics80
- Superterm Circuit Board Main Fuse81
- Superterm Door Strike Fuses81
Upgrading82
- Expanded Memory Upgrade82
- 256K Memory Module82
- Installing the 256K Memory Module82
- 2MB Memory Board84
- Mounting the 2MB Memory Board84
Maintenance86
- Power Supply Replacement86
- Backup Battery Replacement87
- Backup Battery In-Line Fuse Replacement87
- Superterm Step-Down Transformer Replacement88
- Service Entrance Fuse Replacement89
Specifications90
Power Ratings91

Questions and Answers

J
Julie DukeAug 2, 2025
How to fix blown Superterm main circuit board fuse in Continental Access SUPERTERM CIC1800 IP Access Controllers?
- M
  mjacksonAug 2, 2025
  If the Superterm main circuit board fuse is blown, replace the fuse with a 5mm x 20mm long, 10Amp, 250V, slow-blow fuse.
M
Marcus JonesAug 18, 2025
What to do if door strike fuse blown in Continental Access IP Access Controllers?
- G
  Gregory CurtisAug 18, 2025
  If the door strike fuse is blown, replace it with a 2-Amp, SB, 250V, plug-in, slow-blow fuse.

Summary

REGULATORY CONSIDERATIONS

Installer Responsibilities

Covers general and UL294 specific duties for installation.

POWER CONNECTIONS

AC Power and Grounding

Ensures safety and proper electrical connections.

Transformer Connection

Battery Backup Connection

DOOR CONNECTIONS

Wiegand;Proximity Reader Connections

Details connecting Wiegand/Proximity readers.

Magnetic Stripe Reader Connection

Details connecting magnetic stripe readers.

Keypad Connection

Details connecting keypads.

Door Status Sensor Connection

Request-to-Exit Sensor Connection

RELAY CONNECTIONS

Door Strike Relay Operation

Explains LOCAL/REMOTE strike control.

EXPANSION BOARD CONNECTIONS

Supervised Alarm Board

DI;DO Board

SETTINGS

Jumper Configuration

Overview and specific jumper settings for operation.

TROUBLESHOOTING

LED Diagnostics and Fuse Checks

Diagnosing issues using LEDs and checking fuses.

MAINTENANCE

Component Replacement Procedures

Replacing power supply, battery, transformer, and fuses.

Continental Access SUPERTERM CIC1800 Specifications

General

Category	IP Access Controllers
Model	SUPERTERM CIC1800
Manufacturer	Continental Access
Communication Protocol	TCP/IP
Communication Interface	Ethernet, RS-485
Reader Output Voltage	12VDC
Max Doors Supported	2
Power Supply	12 VDC
Reader Compatibility	Wiegand
Inputs	4

Related product manuals

CARDACCESS 3000 - ARCHITECTURAL AND ENGINEERING SPECIFICATION V2.7

50 pages