Control C4-Z2IO - User Manual

11
Package contents
• C4-Z2IO ZigBee IO and Extender
• Four wall mounting screws
• Four plastic dry wall anchors
• Two IR emitters
• Micro USB power supply
Requirements
• Composer Pro 2.10.0 or higher
Features
The ZigBee IO and Extender (Z2IO) is a single device that
combines the features of:
• Remote relays (up to two)
• Remote contact sensors (up to four)
• Remote thermistors (two)
• Internal contact (internal magnetic reed switch)
• ZigBee (IEEE 802.15.4) extender
• ZigBee-to-IR converters
Any of these inputs can be used to trigger and control automated
events—such as sending an e-mail or turning on a cabinet light
when its door is opened—throughout the Control4 system.
With this device, you can extend home automation control to the
most remote of locations and applications inside or outside the
home, reducing the need to run control wires over long distances
(or where you can’t run any wires at all).
As ZigBee to IR
The two 3.5 mm IR ports allow you to connect up to two standard
IR emitters to control any IR-controlled devices, such as TVs,
DVRs, and receivers.
When connecting IR emitters, make note of which port each
emitter is connected to (labeled “1” and “2”).
IR codes sent from the controller to the ZigBee IO and Extender
are cached at the device, resulting in faster IR control response
times.
Micro USB IR 1 IR 2
Note: Y IR cables can be used, or IR cables can be
spliced together (in parallel, not in series), to increase
the number of controlled devices. Be aware that these
connected emitters cannot be controlled independently
but will all fire simultaneously from the shared IR
port. Test to verify that there is no crossover code
functionality between devices sharing the same IR port
to avoid unwanted side eects.
As a contact and relay
The device has an internal contact along one edge that can
be used to detect open or closed states when installed with
a mounted magnet. Up to four contacts (besides the internal
contact) or two additional relays, or a combination of the two,
can be used. Each option is outlined below in “Contact and Relay
Wiring Options,” and after it’s physically wired, the correct option
must be set on the Properties tab as outline further below in the
section “IO Options.”
As a relay
As a relay, this device provides wireless control of garage door
openers, window coverings, fireplaces, and pumps (along with
other relay control applications) inside or outside the home. It
integrates into Control4 systems as standard relays that can be
opened, closed, toggled, or pulsed.
The relay enables wireless control of any device controllable
by one or two low-voltage SPST relays or one simulated SPDT/
DPDT relay. These functions appear in a Control4 system as relay
outputs (relays) in Composer Pro.
SPST
(single pole single throw)
(single pole double throw)
SPDT
(double pole single throw)
DPST
(double pole double throw)
DPDT
ZigBee IO and Extender
Installation Guide

Summary

ZigBee IO and Extender Installation Guide

Package Contents

Lists all items included in the product package.

Device Features

Details the device's combined functionalities.

IR Control Functionality

Explains IR emitter connections and operation.

Contact and Relay Capabilities

Covers internal contact and external contact/relay usage.

Device Functional Modes

Contact Sensor Operation

Explains wireless monitoring via contact sensors.

ZigBee Extender Functionality

Describes mesh extender and router capabilities.

Thermistor and Humidistat Features

Details integrated thermistor/humidistat functions.

Installing the ZigBee IO and Extender

Device Placement and Preparation

Site selection criteria and component separation.

Mounting the Device Tray

Mounting instructions for the device tray.

Wiring and Configuration

Wire Routing and Power Options

Guides wiring and explains alternate power sources.

Device Configuration Steps

Step-by-step guide for device setup.

Connections Overview

Static and dynamic connection types.

Device Properties and IO Options

General and Humidity Properties

Explains general settings and humidity monitoring.

Temperature Monitoring Properties

Covers temperature scale and sensor offset settings.

IO Pin Configuration Options

Explains pin assignments and configuration options.

Device Operation and Troubleshooting

Contact and Relay Status

Status of internal and wired contacts/relays.

Troubleshooting Common Issues

Steps to resolve device issues.

LED Indicators and Button Functions

Explains LED indicators and button sequences.

Firmware Management

Procedure to revert firmware.

Wiring and Resources

Sample Wiring Configurations

Wiring diagrams for common setup options.

Additional Support Resources

Lists resources for further support and documentation.

Safety Information

Electrical Safety Warnings

General electrical safety warnings and instructions.

Important Safety Guidelines

Crucial safety guidelines for product usage.

Safety Warnings

Object Insertion and Moisture Warnings

Warnings against inserting objects and exposure to moisture.

Compliance Statements

USA & Canada FCC Compliance

FCC Part 15 statement on unintentional emissions.

Regulatory Compliance

RF Radiation Exposure Statement

Statement on RF exposure limits and compliance.

European Compliance

CE Declaration of Conformity (English)

Official declaration of conformity to EU directives.

Control C4-Z2IO Specifications