To Next PageTo Next PageWhy is my Cooke & Lewis Washer/Dryer not operating?
Your Cooke & Lewis Washer/Dryer might not be operating due to several reasons. Ensure that there is a proper connection to the power supply and that the power is on. Check that the washer door is completely closed and that the machine has been switched on.
What to do if my Cooke & Lewis BWD60CL Washer/Dryer won't fill with water?
If your Cooke & Lewis Washer/Dryer isn't filling with water, make sure you've pressed the "Start/Pause" button and that the water tap is turned on. Check that the water pressure is not less than 0.03 MPa, the inlet hose isn't kinked, and there isn't a water supply failure. Also, ensure the program knob is properly set, the washer door is correctly closed, and the inlet hose filter isn't blocked.
Why is my Cooke & Lewis Washer/Dryer vibrating so much during spinning?
Excessive vibration during spinning in your Cooke & Lewis Washer/Dryer can be due to several factors. First, ensure all transportation bolts have been removed. Second, check that the washer/dryer is on an even and level surface. Finally, reduce the amount of laundry in the drum if the machine load is over 6 kg.
What to do if my Cooke & Lewis BWD60CL is draining while filling?
If your Cooke & Lewis Washer/Dryer is draining while filling, it could be because the drain hose height is below 80cm. Ensure the drain hose is installed within 80-100cm of height. Also, verify that the drain hose is not submerged in water.
Why is my Cooke & Lewis BWD60CL Washer/Dryer not draining?
If your Cooke & Lewis Washer/Dryer isn't draining, the drain hose may be blocked, so unblock the drain hose. Also, ensure the drain hose end is between 80-100cm above the floor level. Finally, check if the filter is blocked and unblock it if necessary.
Why does my Cooke & Lewis Washer/Dryer stop before finishing the wash cycle?
If your Cooke & Lewis Washer/Dryer stops before completing the wash cycle, check the power supply for water or electricity failure. Also, verify that the "Start/Pause" button is pressed.
Why is there so much foam in my Cooke & Lewis BWD60CL Washer/Dryer?
Excessive foam in your Cooke & Lewis Washer/Dryer could be due to using the wrong type of detergent. Check if your detergent is a low-foaming type. It might also be caused by using too much detergent, so reduce the amount of detergent in the distribution drawer.
Why did spinning fail in my Cooke & Lewis BWD60CL Washer/Dryer?
Spinning might fail in your Cooke & Lewis Washer/Dryer if the machine has been set to drain before spin; wait for a while before initiating spin. Another cause could be an unbalance of the laundry, so reposition the laundry or run a spinning program again.
What does it mean when my Cooke & Lewis BWD60CL Washer/Dryer stops for a while?
If your Cooke & Lewis Washer/Dryer stops for a certain period of time, it may be displaying an error message. Check the display codes for more information.
General| Washer Type | Freestanding |
|---|---|
| Washing Capacity | 6kg |
| Colour | White |
| Programmes | 15 |
| Delay Start | Yes |
| Child Lock | Yes |
Covers essential safety advice, repairs, and pre-use instructions.
Details safe practices for installation, use, and handling electrical safety.
Table listing common faults, their causes, and resolutions.
Instructions for unpacking, installing bottom cover, and removing transit bolts.
Guidance on placing the appliance on a solid surface and adjusting feet for stability.
Instructions for connecting inlet/drain hoses to water supply and drainage.
How to connect to power and perform the initial maintenance wash.
