To Next PageTo Next PageWhy my Cooke & Lewis Washer won't turn on?
If your Cooke & Lewis Washer fails to operate, several factors could be at play. First, ensure there's a solid connection to the power supply. Check the power supply to rule out a power failure. Confirm that the washer door is properly closed. Lastly, verify that the machine is switched on.
How to stop my Cooke & Lewis BWM60CL Washer from vibrating during the spin cycle?
If your Cooke & Lewis washer vibrates excessively during the spin cycle, first check that the transit bolts have been removed. Ensure the washing machine is installed on a flat, level floor. Confirm that all four feet are resting firmly on the floor, pressing down on each corner to ensure the appliance is stable. If it remains unstable, consult the 'Positioning and levelling the appliance' section.
Why my Cooke & Lewis BWM60CL won't fill with water?
If your Cooke & Lewis Washer won't fill with water, make sure you've pressed the 'Start/Pause' button. Check that the water tap is turned on and that the water pressure is at least 0.03 Mpa. Inspect the inlet hose for any kinks. Ensure there is a water supply. Verify that the program knob is correctly set and the washer door is properly closed. Finally, check the inlet hose filter for blockages.
How to fix water leak under Cooke & Lewis washing machine?
If you find water under your Cooke & Lewis washing machine, tighten the drain pump filter. Also, check the drain and inlet hoses to ensure they are fully tightened and undamaged.
Why is my Cooke & Lewis Washer draining while filling?
If your Cooke & Lewis Washer is draining while filling, it could be due to the drain hose being positioned incorrectly. Ensure the height of the drain hose is within 80-100cm. Also, check that the drain hose is not submerged in water.
What to do if my Cooke & Lewis Washer has drainage failure?
If your Cooke & Lewis Washer experiences drainage failure, start by unblocking the drain hose. Ensure the drain hose end is positioned between 80-100cm above the floor level. Also, check and unblock the filter.
Why is there excessive foam in my Cooke & Lewis BWM60CL Washer?
If your Cooke & Lewis Washer is producing excessive foam that spills into the detergent dispenser, it could be due to using the wrong type or too much detergent. Check that your detergent is suitable for automatic washing machines and reduce the amount of detergent you are using.
How to reduce strong vibration while spinning in Cooke & Lewis BWM60CL Washer?
If your Cooke & Lewis Washer is experiencing strong vibrations while spinning, ensure that all transportation bolts have been removed. Confirm that the washing machine is located on an even surface and is properly leveled. Also, avoid overloading the machine by reducing the amount of laundry in the drum.
Why does spinning start late or the machine does not spin in my Cooke & Lewis BWM60CL Washer?
If the spinning cycle starts late or your Cooke & Lewis machine does not spin, the imbalance control system may have activated because the laundry is unevenly distributed in the drum. This may take several attempts before the laundry is evenly distributed and normal spinning can resume. If the laundry is still not evenly distributed after 10 minutes, redistribute the load manually and select the programme again.
Why does my Cooke & Lewis BWM60CL stop before completing wash cycle?
If your Cooke & Lewis Washer stops before completing the wash cycle, check both the water and power supplies to ensure there are no failures.
General| Brand | Cooke & Lewis |
|---|---|
| Model | BWM60CL |
| Category | Washer |
| Language | English |
Overview of the appliance and its components.
Essential safety instructions and warnings for appliance use.
Lists the key features and energy efficiency ratings of the washing machine.
Explains the control panel, buttons, and wash programme selection.
Procedures for daily cleaning, control panel, and detergent drawer.
Guide to identifying and resolving common washing machine problems.
Contains technical specifications, recycling, and disposal information.
Details the manufacturer's warranty terms, conditions, and customer service.
Statement of compliance with European directives.
Appliance and aperture dimensions, and unpacking instructions.
Essential steps to remove transit bolts and level the appliance.
Detailed guide for connecting the appliance to the water supply and drain.
Connecting to power supply and performing the first maintenance wash.
