Coral Series - User Manual

Questions and Answers

K
kevin75Aug 20, 2025
Why is my Coral Water Dispenser not regenerating automatically?
- C
  cranecourtneyAug 20, 2025
  If your Coral Water Dispenser isn't automatically regenerating, there could be several reasons: * The power might not be connected; ensure it is properly connected. * The motor could be defective, requiring replacement. * The turbine might be fouled or defective, needing cleaning or replacement. * The turbine cable may be defective and need replacing. * The turbine cable might not be correctly positioned; push the sensor into the housing fully until it clicks into place.
M
melissarayAug 22, 2025
What to do if the Coral Water Dispenser regenerant tank overflows?
- R
  Rachel GoodwinAug 22, 2025
  If the regenerant tank of your Coral Water Dispenser is overflowing, consider these potential causes and solutions: * Check the drain line for any blockages or kinks. * Clean the refill flow control to remove any obstructions from the ball and seat. * Inspect all connections in the regenerant line for air leaks. * Clean the drain control to remove any resin or debris. * Replace the air check ball if it's sinking (applicable to model 255 only). * Ensure the correct drain control is fitted; a too-small drain control with a larger injector may reduce draw rates. * Remove any obstruction holding regenerant valve disc 1 open. * Remove any obstruction preventing valve disc 2 from closing during regenerant draw.
S
sgonzalezAug 25, 2025
Why is there no conditioned water after regeneration in my Coral Water Dispenser?
- E
  Eric VazquezAug 25, 2025
  If you're getting no conditioned water after regeneration with your Coral Water Dispenser, it could be due to: * Insufficient salt in the tank; add salt, ensuring the level is above the water level. * A plugged injector; clean the injector and screen. * The air check closing prematurely; check connections for air leaks and inspect the air check ball (model 255) to ensure it floats.
L
Leslie NavarroAug 26, 2025
Why does my Coral Water Dispenser regenerate at the wrong time?
- K
  Kayla LopezAug 26, 2025
  If your Coral Water Dispenser regenerates at the wrong time, the settings are likely incorrect. Correct the settings to resolve this issue.
L
Linda HallAug 27, 2025
What to do if Coral Water Dispenser has hard water after regeneration?
- R
  rsotoAug 28, 2025
  If you're experiencing hard water after regeneration with your Coral Water Dispenser: * Repeat the regeneration process after verifying the settings. * Check settings and adjust if required.
W
wallacecodyAug 29, 2025
Why does Coral Water Dispenser use more or less salt than the setting?
- I
  Ian BryantAug 29, 2025
  If your Coral Water Dispenser uses more or less salt than the set amount, there might be foreign matter in the valve causing incorrect flow rates. Remove the brine control and clean out any debris. Then, run the system through a regeneration cycle to flush the valve.
H
Haley GrahamAug 31, 2025
What to do if Coral Water Dispenser runs out of conditioned water between regenerations?
- C
  Christopher PearsonAug 31, 2025
  If your Coral Water Dispenser runs out of conditioned water between regenerations, consider the following: * Repeat regeneration after checking the correct regenerant dosage is set. * Ensure the correct salt setting is applied. * Verify that the hardness or capacity settings are accurate. * Adjust the hardness setting if the water hardness has increased. * Ensure the salt level is above the water level.
M
Matthew WalkerSep 2, 2025
What causes Coral Water Dispenser valve to not draw brine?
- L
  Lauren FletcherSep 2, 2025
  If the valve on your Coral Water Dispenser isn't drawing brine, it could be due to: * A restricted drain line; check for blockages or kinks. * A plugged injector; clean the injector and screen. * A defective injector; replace the injector. * The air check closing prematurely; put control into brine draw C2 to check. Repair or replace if needed.
A
Alexis KeySep 4, 2025
Why is there water flow from drain or regenerant line when Coral Water Dispenser is in service?
- J
  Jason HernandezSep 4, 2025
  If you notice water flowing from the drain or regenerant line of your Coral Water Dispenser while it's in service, it could be due to debris stopping flapper valve from closing. Remove debris.
B
baileymillerSep 6, 2025
Why will Coral Water Dispenser not draw regenerant or intermittent or irregular draw?
- J
  Jessica JamesSep 6, 2025
  If your Coral Water Dispenser isn't drawing regenerant, or the draw is intermittent/irregular: * Check drain line is not blocked or kinked. * Clean injector and screen. * Replace injector.