CORONA RP6D1 - Caution; Installing the receiver

Caution:
Caution:
Caution:
Caution:
1.
1.
1.
1.
Restart
Restart
Restart
Restart
the
the
the
the
receiver
receiver
receiver
receiver
when
when
when
when
the
the
the
the
set
set
set
set
up
up
up
up
process
process
process
process
of
of
of
of
disabling
disabling
disabling
disabling
or
or
or
or
enabling
enabling
enabling
enabling
the
the
the
the
failsafe
failsafe
failsafe
failsafe
is
is
is
is
completed.
completed.
completed.
completed.
2.
2.
2.
2.
While
While
While
While
in
in
in
in
Mode
Mode
Mode
Mode
I,
I,
I,
I,
Mode
Mode
Mode
Mode
II
II
II
II
or
or
or
or
Model
Model
Model
Model
III
III
III
III
you
you
you
you
can
can
can
can
cut
cut
cut
cut
power
power
power
power
to
to
to
to
cancel
cancel
cancel
cancel
the
the
the
the
setting
setting
setting
setting
process.
process.
process.
process.
Do
Do
Do
Do
not
not
not
not
cut
cut
cut
cut
power
power
power
power
i
i
i
i
n
n
n
n
the
the
the
the
process
process
process
process
of
of
of
of
locking
locking
locking
locking
receiver,
receiver,
receiver,
receiver,
disabling
disabling
disabling
disabling
failsafe
failsafe
failsafe
failsafe
or
or
or
or
enabling
enabling
enabling
enabling
failsafe.
failsafe.
failsafe.
failsafe.
Otherwise
Otherwise
Otherwise
Otherwise
your
your
your
your
receiver
receiver
receiver
receiver
may
may
may
may
be
be
be
be
damaged.
damaged.
damaged.
damaged.
3.
3.
3.
3.
After
After
After
After
enabling
enabling
enabling
enabling
failsafe,
failsafe,
failsafe,
failsafe,
please
please
please
please
readjust
readjust
readjust
readjust
the
the
the
the
transmitter
transmitter
transmitter
transmitter
settings
settings
settings
settings
of
of
of
of
sticks
sticks
sticks
sticks
and
and
and
and
switches
switches
switches
switches
for
for
for
for
the
the
the
the
correct
correct
correct
correct
flight
flight
flight
flight
conditions.
conditions.
conditions.
conditions.
Installing
Installing
Installing
Installing
the
the
the
the
receiver
receiver
receiver
receiver
1 . Plug in all the servos/ESC. Pay attention to the polarity of the connectors. Please consult the labels on the case for the channel numbers
and polarity.
Caution:
Caution:
Caution:
Caution:
If
If
If
If
the
the
the
the
polarity
polarity
polarity
polarity
of
of
of
of
the
the
the
the
plugs
plugs
plugs
plugs
is
is
is
is
wrong,
wrong,
wrong,
wrong,
it
it
it
it
can
can
can
can
damage
damage
damage
damage
the
the
the
the
servos/ESC.
servos/ESC.
servos/ESC.
servos/ESC.
2 . If not using an ESC with a built in battery eliminator circuit (BEC), plug a 4.8V battery/switch harness into any unused channel. If you are
using all the channels for servos, use a Y harness to connect the battery and servo to 1 channel.
3 . Wrap the receiver in foam to isolate it from vibration and secure it in the aircraft with for instance a rubber band.
4. Unwind the antenna fully. Do not coil or cut the antenna.