Cotech 18-125 User Manual

GREAT BRITAIN • CUSTOMER SERVICE tel 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk postal 10 – 13 Market Place, Kingston upon Thames, Surrey, KT1 1JZ
Ver. 20180615
Remote Switch, 3-Pack
Art.no 18-1255 Model 3 x 51058GBX10 + 50074
36-6010 3 x 51058X10 + 50074
Please read theentire instruction manual before using
theproduct and then save it for future reference. We reserve
theright for any errors in text or images and any necessary
changes made to technicaldata. In theevent of technical
problems or other queries, please contact our Customer
Services.
Safety
• This product is suitable for switching products such as
lights on andoff.
• Make sure that thelight is turned off before connecting it
to theproduct.
• Never connect alight with ahigher power rating than
1000 W.
• This product is intended for indoor use, do not expose it
to rain or moisture.
• Make sure that theelectrical socket that theremote
control switch is plugged into is easily accessible in
case theswitch and connected product need to be
disconnected from themains electricity quickly.
• Do not connect after each other.
• Do not cover theproduct.
Operating instructions
Installation
In order to use theremote switches, thereceivers and
theremote control must first be wirelessly connected (paired).
Thisis where you get to decide which receiver is to be
controlled by which button on theremote control.
7. Repeat steps 2 to 5 for theother receivers.
Tip:
• You can connect more than one receiver to thesame
button,e.g. [ A ], on theremote control. Thiscould
be useful if you like switching several lights on at
thesametime.
• You can connect multiple remote controls to thereceivers.
Eachreceiver has amemory for up to 6 different remote
controls or transmitters.
Switching on/off
2. TheLED in thebutton will start flashing slowly.
Thereceiver is now ready to delete theremote control.
3. Pressin theoff-button on theremote control (make sure
to choose thecorrect off-button). Theremote control will
now be deleted from thereceiver.
Note: Thelight can still be switched on/off manually by
pressing thebutton on thereceiver.
Deleting all paired remote controls
1. Holdin thebutton on thefront of thereceiver for 6seconds
until theLED in thebutton starts flashing quickly.
2. WhentheLED stops flashing, all theremote controls
which were paired with thereceiver will have been deleted.
Changing the batteries
1. Pryoff thebattery cover using acoin or screwdriver.
2. Remove thebattery and replace it with anew CR2032
battery. Thepositive terminal (+) of thebattery should face
upwards as shown in thepicture.
Responsible disposal
This symbol indicates that this product
should not be disposed of with general
householdwaste. Thisapplies throughout
theentire EU. Inorder to prevent any harm to
theenvironment or health hazards caused by
incorrect waste disposal, theproduct must
be handed in for recycling so that thematerial
can be disposed of in aresponsible manner.
Whenrecycling your product, take it to your
local collection facility or contact theplace of
purchase. Theywill ensure that theproduct is
disposed of in anenvironmentally sound manner.
1. Remove theplastic
tab from theback of
theremote control to
activate thebattery.
3. Holdin thebutton on
thefront of thereceiver
for at least 3 seconds and
then releaseit.
2. Plugthereceiver into
awall socket.
4. TheLED button will
start flashing slowly.
Thereceiver is now
in learning mode and
ready to be paired with
theremote control.
5. Single-press one of
theon-buttons on
theremote control (A,
B, C or D). TheLED on
thereceiver will shine
steadily once theremote
control has been paired.
6. Connect alight to
thereceiver and
check that thelight is
switchedon.
Use thebuttons in theleft-
hand “ON” row to switch
thepaired light on and
thebuttons in theright-
hand “OFF” row to switch
thelightoff.
Deleting a paired remote control
You might need to delete aremote control from thememory
of thereceiver in case you wantto:
• control thereceiver using another button on theremote
control.
• pair anadditional remote control, but all 6 memory slots
are occupied.
1. Holdin thebutton on
thereceiver you wish to
delete theremote control
from for 3 seconds and
then releaseit.
Care and maintenance
• Unplug thereceiver from thewall socket and remove
thebattery from theremote control if they are not to be
used for anextended period.
• Clean theunits by wiping them with adrycloth.
Troubleshooting guide
Theremote
switch set is
not working.
• Has thereceiver been paired with
aremote control as describedabove?
Trypairing themagain.
• Check thebattery of theremote control.
• Is theremote control too far away from
thereceiver (25m)?
• Check that thelight is properly
connected to thereceiver and that it is
switched on and not faulty.
• Try plugging thelight into another
electrical outlet to make sure that
itworks.
• Is there electricity in theoutlet
thereceiver is pluggedinto?
Specifications
Frequency 433.92 MHz
Receiver
Power supply 220–240V AC, 50 Hz
Maxrange 25m
Max load 1000 W (resistive load)
Memoryslots 6
Remote control
Battery 1×CR2032, 3 V DC (included)
Number of channels 4

Cotech 18-125 Specifications

General

Brand	Cotech
Model	18-125
Category	Switch
Language	English