Cover Pools Save-T Cover II

Other manuals for Cover Pools Save-T Cover II

Installation & Owner's Manual5 pages

Questions and Answers

N
Nina RileyAug 13, 2025
How to fix a flashing red LED on Cover Pools Lighting Equipment Touch Pad and Receiver when the motor won't run?
- C
  Corey SanfordAug 13, 2025
  If the red LED is flashing on your Cover Pools Lighting Equipment's Touch Pad and Receiver, and the motor isn't running, it could be due to several reasons. The receiver memory might not have been cleared, or the Touch Pad hasn't been programmed correctly. In rare cases, the Touch Pad might be sending an incorrect signal. To resolve this, try clearing the memory and reprogramming the Touch Pad. If that doesn't work, you may need to replace the receiver or the Touch Pad.
B
Brandon PughAug 17, 2025
What to do if both LEDs flash and the relay clicks but the motor won't run on Cover Pools Lighting Equipment?
- L
  Laura WilliamsAug 17, 2025
  If both LEDs are flashing and the relay clicks, but the motor doesn't run on your Cover Pools Lighting Equipment, it could be due to: * Only one power wire connected to the receiver. * A bad motor. * A wet motor. To fix this, connect power wires to both the black and black with red trace connections. If that doesn't solve the issue, consider replacing or servicing the motor.
J
John WhiteAug 20, 2025
Why does my Cover Pools Lighting Equipment cover stutter when it moves?
- E
  Ethan PenningtonAug 20, 2025
  If your Cover Pools Lighting Equipment cover stutters as it moves, it may be due to: * A mechanical problem like water on the cover, pulleys, gliders, or splices. * Poor RF reception. * The Touch Pad button not being pushed continuously. To address this, first correct any mechanical issues. Then, adjust the position of the antennae or Touch Pad to improve RF reception. Ensure you push the button continuously and firmly on the center.
A
Albert HardyAug 25, 2025
Why does my Cover Pools Lighting Equipment only run in one direction?
- A
  Ashlee GarciaAug 25, 2025
  If your Cover Pools Lighting Equipment runs in only one direction (hydraulic system), it could be due to several reasons: * Either the black or black/red wires are not receiving power. * A fused relay. * The Touch Pad is not broadcasting in one direction (rare). * A loose relay. * A wet motor. * A bad hydraulic solenoid. Check the wire connections and ensure power is supplied to both wires. If power is supplied separately, check both sources. Try changing the relay or Touch Pad. Also, tighten the relay in its socket, service the motor, or replace the solenoid.
V
vpattersonAug 28, 2025
What causes the receiver relay to chatter when changing direction on Cover Pools Lighting Equipment?
- A
  Anthony GrantAug 28, 2025
  If the receiver relay chatters when the direction is changed on your Cover Pools Lighting Equipment, it may be due to: * Insufficient current, where the motor pulls current from the relay at start-up. * A bad relay. To resolve this, replace the GFCI if necessary. You can also combine two power wires from one breaker to the power connection on the Receiver Board, or provide a larger gauge wire. If the problem persists, replace the relay.
S
Shannon HernandezSep 1, 2025
Why does my Cover Pools Lighting Equipment motor only hum, and the relay may click?
- M
  Melissa RivasSep 1, 2025
  If the motor only hums and the relay may click on your Cover Pools Lighting Equipment, the issue might be due to: * The relay being out of socket. * The relay being loose. * Burnt motor start windings. * A wet motor. To fix this, insert the relay and ensure it is tightened in the socket. If that doesn't work, you may need to replace or service the motor.
A
Aaron OsborneSep 5, 2025
What to do if the Touch Pad LED doesn't flash when the button is pushed on Cover Pools Lighting Equipment?
- A
  Andrew BonillaSep 5, 2025
  If the Touch Pad LED does not flash when the button is pushed on your Cover Pools Lighting Equipment, it could be due to a dead battery or poor connection. It can also happen if the key magnet is broken off. Replace the battery (solder in). Re-attach the magnet.
R
Rachel GonzalezSep 8, 2025
What causes a Cover Pools Lighting Equipment Receiver Board to spark and burn at R12?
- D
  Dr. Kristin HatfieldSep 8, 2025
  If the Receiver Board sparked and burned at R12 (just above the black wire to the motor) on your Cover Pools Lighting Equipment, it is not repairable. You need to change the board.