To Next PageTo Next PageWhy does my Craftsman 247.27050 leave an uneven cut?
An uneven cut from your Craftsman Lawn Mower can be caused by: * The deck not being leveled properly. Perform a side-to-side deck adjustment. * A dull blade. Sharpen or replace the blade. * Uneven tire pressure. Check the tire pressure in all four tires.
What to do if my Craftsman 247.27050 Lawn Mower engine runs erratically?
If your Craftsman Lawn Mower engine is running erratically, consider these potential causes: * The riding mower might be running with the choke activated. Check that the electric choke is working. * The spark plug wire may be loose. Connect and tighten the spark plug wire. * There may be a blocked fuel line or stale fuel. Replace the fuel line. Fill the tank with clean, fresh gasoline and replace the fuel filter. * The vent in the gas cap may be plugged. Clear the vent or replace the cap if damaged. * There might be water or dirt in the fuel system. Drain the fuel tank and refill with clean, fresh gasoline. * The air cleaner may be dirty. Clean or replace the air cleaner paper element or clean the foam pre-cleaner.
Why is my Craftsman 247.27050 engine overheating?
Your Craftsman Lawn Mower engine may be overheating due to: * Low engine oil level. Fill the engine with the proper amount and type of oil. * Restricted air flow. Clean grass clippings and debris from around the engine’s cooling fins and blower housing.
How to reduce excessive vibration in my Craftsman 247.27050 Lawn Mower?
Excessive vibration in your Craftsman Lawn Mower could be due to: * Loose or unbalanced cutting blades. Tighten the blade and spindle and balance the blade. * A damaged, dull, or bent cutting blade. Replace the blade.
What causes a Craftsman Lawn Mower engine to idle poorly?
A Craftsman Lawn Mower engine may idle poorly due to: * A fouled spark plug. Replace the spark plug and adjust the gap. * A dirty air cleaner. Clean or replace the air cleaner element and/or clean the pre-cleaner.
Why does my Craftsman Lawn Mower engine hesitate at high RPMs?
If your Craftsman Lawn Mower engine hesitates at high RPMs, it might be because the spark plug gap is set too close. Remove the spark plug and adjust the gap.
General| Brand | Craftsman |
|---|---|
| Model | 247.27050 Series |
| Category | Lawn Mower |
| Language | English |
Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate.
Engine exhaust and vehicle components contain chemicals known to cause cancer and reproductive harm.
Slopes are a major factor related to loss of control and tip-over accidents. Exercise extra caution.
Tragic accidents can occur if operator is not alert to children's presence. Keep them away.
Follow manufacturer recommendations for weight limits and towing on slopes.
Machine should not be used on or near unimproved forest-covered land unless equipped with a spark arrestor.
Depicts and describes safety symbols that may appear on the product.
General setup, including manual mower movement via hydrostatic relief.
Step-by-step guide for installing the operator's seat onto the riding mower.
Repositioning drive controls and connecting battery cables.
Installing discharge chute deflector and checking tire pressure.
Adjusting seat position and understanding fuel recommendations.
Guide to activating the Smart Lawn App via Bluetooth.
Overview of key controls like throttle, PTO, ignition, and display indicators.
Detailed steps for starting, stopping, and safety interlock checks.
Instructions for driving, steering, and maneuvering the tractor safely in forward and reverse.
How to safely engage PTO and perform mowing operations.
Using Reverse Caution Mode and executing zero-turn maneuvers.
A chart detailing service guidelines and recommended maintenance intervals.
Procedures for cleaning the tractor and deck after use.
Guidelines for engine maintenance and preparing the tractor for storage.
Information on battery maintenance, charging, and servicing the electrical system.
Checking transmission oil and adjusting drive control levers.
Procedures for leveling the mower deck and adjusting gauge wheels.
Instructions for deck removal/installation, belt replacement, and blade care.
Procedures for preparing and storing the riding mower for extended periods.
Steps to take to prepare the mower after storage for operation.
Common causes and remedies for an engine that fails to start or runs erratically.
Addressing overheating, hesitation, poor idling, and excessive vibration.
Causes and solutions for an uneven cut.
