Craftsman CMCST910 - Maintenance

13
ENGLISH
Versatrack™ (Fig. O)

WARNING: To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can causeinjury.

WARNING: To reduce the risk of serious
personal injury, do not use a damaged Versatrack™
hang hook or Versatrack™ Trackwall. A damaged
Versatrack™ hang hook or Versatrack™ Trackwall will
not support the weight of thetool.

WARNING: To reduce the risk of serious
personal injury, DO NOT suspend tool overhead or
suspend objects from the hang hook. ONLY suspend
tool on the Versatrack™ Trackwall using the hanghook.

WARNING: Ensure that the tool weight
does not exceed the maximum rated weight of 20lb
(9kg) for the selected Versatrack™hook.

WARNING: When hanging objects on a
Versatrack™ Trackwall rail, adequately space the tools
in order to not exceed 75lb (35 kg) per linearfoot.
IMPORTANT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwallsystem.
1. Turn the tool off, remove the battery pack
and accessories.

CAUTION: Any product with exposed
cutting teeth must have them covered securely if it is to
be on theVersatrack™Trackwall.
2. Flip or pull open the integral hang hook
31
. It clicks
when locked intoposition.
3. Mount the integral hang hook to the
Versatrack™Trackwall.
NOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Remove CurrentGuard
1. Remove the guard screw
19
shown in Fig.E.
2. Slide the guard
9
off.
Assembling the New Guard
1. Slide the guard into place as shown in Fig.F.
2. Replace and securely tighten the guard screw
19
.
Replacing Guard (Fig.E, F)

WARNING: Never operate appliance
without guard firmly in place. Damage or personal
injury couldresult.
Accessories

WARNING: Since accessories, other than
those offered by CRAFTSMAN, have not been tested
with this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with thisproduct.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact CRAFTSMAN call 1-888-331-4569 .
Cleaning

WARNING: Blow dirt and dust out
of all air vents with clean, dry air at least once a
week. To minimize the risk of eye injury, always
wear ANSI Z87.1approved eye protection when
performingthisprocedure.

WARNING: Never use solvents or other
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
aliquid.
MAINTENANCE

WARNING: To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories,
when replacing line, or prior to cleaning. An
accidental start‑up can causeinjury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on
neatly and in layers. Do notcrisscross.
7. When the wound cutting line reaches the recesses
30
,
cut theline.
8. Fit the spool onto the appliance as described in
Replacing SpoolAssembly.